There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi,
I would like to know if there is an event from peripheral side to indicate that the discovery process is over.
The gold is to disconnect from the central if all the...
1.Would you please confirm the maximum ripple range that nrf52832 can accept for VDD (3.3V) and dec4 (1.3V) power supply, that is to ensure that the function will not be affected...
Hello,
I have used the Nordic Thingy application, I also used the Raspberry Pi Python interface and I observed the temperature measured.
The temperature is not stable...
I have a customer requesting any version above 0.8.5 for part number nRF9160-DK.
Can you tell me what date codes would have the requested versions?
thanks,
Russ
QB79869...
I'm looking for a low energy communication method for a wireless PIR motion sensing device. The system will be battery powered so RX current draw is particularly important...
We are revising a design using the NRF9E5, we are experiencing problems with the third harmonic when configured for 915MHz band, the higher we go up the band the worse the...
I am looking to build a custom board using nrf52840 and want both UART and flashing capabilty on the custom board. I have a NRF52840dk that I will use to program the custom...
I want to increase the pull-up resistor value to educe the current consumption.
but, I am afraid that the GPIO input will not be recognized as High.
I want to know the...
Hi,
I can't find this information anywhere in the AT command manual or datasheet. What is the accuracy for " AT%XTEMP?" and "AT%XRFTEST=10,1,0"?
Kind regards,
Thoma...
Hello,
I'm trying to generate project to realise new user-cases with wireless mesh networks.
I did a demo with the Thingy52 at flower greenhouses
They are very interested...
HI! I've done the basic Blinky and UART examples, and now have to move on to programming something on my own. ( I have to send EEG signals from one BLE board to another/notebook...
hai ,
i tried nrf52840 ota over BLE from third party (ESP32).
As per the DFU protocol implemented logics and upto init packet (.dat file) getting expected response from...
Hi, I'm looking to use P15 (Shield Debug out connector) on nRF9160-DK. Description here https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrf91_dk%2FUG%2Fnrf91_DK%2Fhw_debug_out...
Hi I used the light ctl/lc example project and connected to it with my iphone app which uses nordic sdk. I made a slider which sends messages quite often to the mesh device...
We are presently using Raspberry Pi 3 Model B to observe BLE packets coming from sensors that have NRF52.
We are also able to do DFU OTA using the Nordic NRF52840 USB dongle...
