Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi,
We are using nrf52840, with SDK 16.0. we wanted to know that How does Garbage collection works?!
Does it reuse the allocated pages by erasing it or it uses the new...
I am just starting out. Trying to figure out how to interact with the board and my tool chain. I'm not sure how to flash a merged.hex file I made (serial_lte_modem) into the...
Hi,
I am using the nRF54L15-DK board and would like to use the driver code for the peripheral(Timer,SPI etc).The SDK I am using is NCSv2.9.0,Please help me find the driver...
Hi everyone, Is there a demo or project code showing BLE transfer between two Nordic chips/devkits with a data rate more than 2mbps using 4mbps phy? Thanks.
Hello,
how is it possible to determine the SDK and Toolchain used when opening an NRFconnect Terminal in VSCode.
It automatically opens the terminal with the 2.8 Toolchain...
Hello,
For my project, I want to develop a Zigbee coordinator for the Thingy:91 that receives reports from end devices and it publishes the values to the cloud. I've developed...
I am currently running nRF Connect Desktop App on Apple M2 chip (ARM64 ; 23.6.0 Darwin Kernel Version 23.6.0)
I have installed nrfconnect-5.1.0-arm64.dmg
Two major issue...
I can read above 3000 samples from accelerometer, before connecting to BLE, but after connecting to BLE the data rate reduces to 200 samples. This is clearly checked and identified...
I have been using VS Code and nRF Connect extensions for over 1 year. I run on a Mac Mini computer with Apple M2 processor. I recently updated the macOS to Sequoia Version...
I'm trying to build my project for nRF54L15 DK. The project uses mcuboot. When mcuboot is being built, I get following warning:
I guess the problem is caused by the config...
Hi, DevZone,
Our customer, Hosiden Osaka, wants to get the recommened foot print regarding nRF54L15, that is, the following each land pattern respectively;
- WLCSP 300um...
I am writing a program for the nRF52805 for use in a battery-operated remote. It needs to wake up from sleep when any button is pressed, perform the interrupt (blinking an...
I have found that in NCS SDK 2.6.2 it was very simple to enable FLASH_SIMULATOR as part of the mcuboot configuration overlays. But starting from SDK 2.7.0, I keep getting...
