Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
i can't create multiple services with the same base uid-128 bit and two service id 16 bit i have created one and its working . this is my code and the error is
Hi,
We are using nRF Connect for Desktop as the production fixture to test the BLE function of our products. To automate some testing procedures in production, we want to...
The advertising PHY is set to 1M; is it fixed? If so, I'd like to understand the reason by reviewing the relevant technical documentation. In the example, it is set to AUTO...
Hello.
I have an nRF9160DK and an nRF7002DK. My goal is to set the nRF9160DK to use the nRF5340 as a module to connect to Bluetooth.
There are two main things I want to...
Hello,
I am considering implementing SPI communication as the transport layer for mcumgr in my application. The setup involves an nRF52820 as an SPI slave and an nRF52840...
Hi everyone,
I am using the S25FL064L memory with the nRF52840 microcontroller and I have a reading problem.
I can read the memory using READ4O mode (opcode 0x6B) but...
Hi Nordic Team,
I'm trying to enable modem tracing on the gnss sample code on my nrf9160dk but have been getting the following error:
Per suggestions on similar threads...
Hi All.
Regarding this exercise, are we sure there is no bug in the https://academy.nordicsemi.com/courses/nrf-connect-sdk-fundamentals/ documentation?
After installing...
before setting NRF_POWER -> SYSTEMOFF = 1, I chose a switch button and an accelerometer as external wake-up sources.
both of the wake-up sources can wake up the chip in...
Hi,
I have an application called `main_repo` built using v2.1.1 (the SDK version doesn't really matter). This contains all source code, dts files, Kconfig files, etc. to...
hello Nordic
trying to migrate from ncs 2.5.0 to 2.7.0
well i did the mistake of installing the toolchain via the vs code .. for some reason it installed it in the wrong...
DFU is now implemented on ipads and iphones, as well as on Android phones, and the app platform is nRF Connect. The problem is that the firmware upgrade can be achieved normally...
I was trying to build off of the example of Lesson 6, exercise 3 from the Intermediate course on DevAcademy.
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate...
Hi there,
I am trying to interface SPH0465 microphone with nRF Dev Kit 52832 with the following configurations of I2S:
I have followed the code from echo example...
