Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello
Is there a possibility to build MCUBoot, SoftDevice, Firmware Loader and Application separately and then merge it manually? Or to build MCUboot + SoftDevice + Firmware...
Hello there,
I am working on a project which involves nRF52840 to scan and connect to specific BLE beacon.
So while scanning, nRF writes scanned data on UART. On same...
Hello,
I'm running SDK v.2.8.0 and developing using the nRF5340 Audio DK. I've successfully flashed using the buildprog.py script, and have set up my DK as an Auracast source...
Hi
1. At nRF5340 datasheet page 420, the PDM duty cycle is 40%~60%, any register can tune duty cycle? Or it's nRF5340 variation tolerance?
2. Since our DMIC IM69D128S...
Hi all,
I'm testing Skylo NTN on nRF9151 SMA DK with the latest pre-commercial/alpha NTN modem firmware (downloaded mid-December 2025).
Registration works fine, and uplink...
I am trying to get the nrf/sampoles/bluetooth/direct_test_mode working together with the code from zephyr/samples/subsys/usb/dfu-next.
I have the DTM mode running correctly...
Hello,
I think there is typo on page 541, in the PWM, Pulse Width Modulation, section of the nRF52840 Product Specification V1.11.
It states "pulse with modulation", but...
Hello,
I have a question concerning the neighbor cell measurement feature on my nRF9160.
After some tests, it seems to be sensitive to the operation mode. For example...
I am currently working with nRF52810 using nRF Connect SDK v3.2.1 , and I am trying to run the AES CCM PSA Crypto sample .
However, when running the unmodified sample, it...
hello i am new to the nrf trilateration and direction tracking using nrf52840, i need some help with the sdk and programming and working examples .
eg : I have 4 nrf52840...
Unable to connect JLink via USB. Installed different versions of JLink without success. Device Manager showns "J-Link driver" under Universal Serial Bus controllers and nrfutil...
I'm using a custom development board and I want to enable timer 0 through the external 32MHZ crystal oscillator. Here is my configuration:
prj.config: # Enable the UART...
I am trying to live capture and analyze traffic on Wireshark. I followed lessons like https://academy.nordicsemi.com/courses/bluetooth-low-energy-fundamentals/lessons/lesson...
