Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hi Team,
I want to develop an application based on Mesh5.0, but I also want to use functions that in nRF SDK. I find the sd_app_evt_wait() in the main function. But in NRF...
Hi,
I have setup a provisioner using the provisioner example of the mesh sdk.
I have also setup 10 nodes using the on_off example of the mesh sdk.
I have provision...
Hi all,
I have successfully followed this [tutorial]( https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/using-a-custom-secure-partition-manager...
Hi!
I am trying to flash a component on my custom embedded PCB that embarks a NRF52832 through BLE. To do this, I run on my PC a python script that reads from a hex file...
How to enable Read back protection in nrf52832 and in nrf52840 after DFU completed.
i have tried using --rbp all its working but i want to do in code(any register or by...
Hi, I'm using the PCA10056 with NRF52840 and I'm using the P24 Section, there's a pin that doesn't have number and neither is connected to GND...
(the pin in the right down...
Good day!
I've found that with connected proxy and enabled filter node only forwards messages and doesn't use advertising. I didn't found in Mesh Profile v1.0.1 any mention...
I'm using a nRF9160-DK (PCA10090) but I can't see connected device on Programmer (v2.0.0) nor LTE Link Monitor (v2.0.0), both installed and launched through nRF Connect for...
I recently installed the nRF Connect extension for VS Code on my PC(Windows 11, 10700k).
I cannot see my connected boards.
But the "programmer" of the nRF Connect...
I have tried a lot but my DK wont enter in Bootloader mode, or atleast the Bootloader folder does not show up in my Windows 7 machine. I am able to do that comfortably with...
I am trying to program the nRF52840 Dongle with the HEX file according to "Programming the nRF52840 Dongle". The dongle is connected to USB port and the LD2 is pulsing red...
On IN141 Informational Notice v1.1 changes for nRF52840 to revision 3 (build code Fx0) are presented.
One of the changes is "New (optional) filter coefficients for pulse...
Hi all,
I am currently developing audio sampling on a custom board using the nrf52832. I'd like to sample at 20khz and am using the nrfxlib driver for this ( https://github...
Hi everone!
I am developing with SDK17.0.2 and using the nordic NUS peripheral example.
I am seeing a strange effect:
I am connecting from an android mobile and when...
