Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hey all!
We want to improve the accuracy of the localization of our asset tracking solution, in particular indoors. For that we want to scan Wifi base station advertisments...
Hello,
I am trying to get an MQTT TLS connection to AWS up and running on my thingie91 (nrf9160). I am using SDK 1.5.0 and the sample "aws_iot".
Even though there is a...
Hello,
what is the CPU speed of nRF52832?
I'd like to test if the NRF52832 is running at 32MHz or 64MHz.
I used it to run a compression algorithm, which took 8ms to...
I have seen this question asked a few times--but every thread seems to have no concrete answer.
I have uninstalled and reinstalled all JLINK drivers.
But still get the...
I am using the nRF9160 for IOT with the console connected on UART 0 there is a string of +CSCON: 1 and +CSCON: 0 messages displayed.
Build Zephyr 1.5.1
Modem firmware...
We're looking for some clear documentation for implementing OTA DFU via BLE on the iOS side. We have the firmware working well on our dev kits here, but working only with...
Hi,
Can you explain please why do you use all flash space for application (except SD area) in your examples. For example, SDK 17.0.0, HRS s132 example starts from 0x26000...
Hi
I have nRF SDK 17.0.2, and looking for ble_app_template application for PCA10100 to be flashed into nRF52833 DK. But seems that is not available.
Is there any other...
I'm developing a C implementation for nrfutil to make a Serial DFU in bootloader of sdk11. But I'm having an issue in serial communication. I've used a serial sniffer to compare...
I am using nRF52840 DK and connecting it with SPI to ESP32. The first bit of the transmission is missed for some reason. I could verify that the transmission is ok with logic...
Hi Nordic,
I'm working on a project using SDK 15.3, s140 , based on the LESC example for a central and peripheral application. I am able to bond with devices and later on...
Hi,
The MMD example published by the Nordic Team ( https://github.com/NordicPlayground/j-link-monitoring-mode-debugging ) is supposed to work with the nRF52DK (PCA10040...
Hi,
We have a custom board with nRF52840 based ISP1807 and developed the fw to some point. For some reason we tried to run the same fw on the nRF52840 DK rather our custom...
I'm trying to program an nRF52810 on a custom PCB using the nRF52-DK and am getting this error ((0x4) Lowlevel error: Unknown value (ffffff24)) when connecting with nRF Connect...
