Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Greetings,
I have two nRF52840's where one is modeled as a peripheral and the other as a central. I have created a custom service and characteristics on the peripheral...
hello Nordic
i work with nrf52840, SDK16.0 S140
i use QSPI for writing to an external flash (IS25LP064A)
if i write 16 bytes then its all ok but if i try to write...
Hello,
I have nrf52810 with soft device S132 5.1, SDK 14.2.
It works fine when NRF_LOG_ENABLED is enabled, data from NUS are printed in debug console. But Im not able...
Hello,
I am writing a BLE central application that connects to a device and should then discover ALL services on the device. I am new to Nordic and am using the nRF5340...
Hi
I am going to start an application with the mesh network. Here is my requirement,
1. I have to receive the data from the master device (STM32) by using SPIS (nRF52840...
Hello,
I am using the ble_app_uart_c_pca10056_s140 example code (SDK v17). This is the NUS BLE central device.
The code is almost unchanged from the example source.
...
I'm quite new to nrf.
These days I'm trying to program power efficient uart data sender over ble.
It receives uart and sends data fine.
The problem is it's not going...
Hello,
Does nRF52833 has support for FreeRTOS in version 16.0.0 of nrF SDK?
Is there any specific example with the softdevice and FreeRTOS?
Thank You,
Vineeth...
When we develop out product, we found it cannot connect to our server. After our check step by step, we found if we comment the code about RAI setting, MQTT service can be...
I wanted to add TWI functionality to the flash fds example and was confused about adding drivers with CMSISwizard. I manually added all the necessary twi drivers based off...
HI
I have got a new nrf5340 DK. I have tested four LEDs and HRM. It's working fine. But when I have tried to upload blinky or hello_world Sample from NCS v1.5.1, I can't...
Hi all,
I have tested successfully the wireless timer syncronization proposed by:
https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts...
Hello guys.
I recently discovered that you included example codes for OSDP Control Panel (CP) and Peripheral Devices (PDs). In NCS v1.5.1 that I am using, they can be fund...
Hello,
I'm using the Infineon Optiga Trust X chip for ECDSA signature verification but I'm having trouble saving the public key.
Currently the public key is generated...
