Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hello,
I was recently trying out some samples with the nRF9160 DK and I had run into some issues when trying to run the nRF Cloud Client Application .
I had flashed...
Hi,
I'm developing on the nRF52 DK which has the nRF52832 chip.
I have a small vibration motor which I'd like to control on/off through one of the boards GPIO pins. At...
Hi,
I'm trying to modify the light bulb example and turn it into a light switch (not a light switch that controls another bulb in the network), but I'm quite new on the...
Hi,
I've noticed that there was an issue with ble_nus in SDK 15.3 - detailed in this post .
I'm using SDK 17, and in my application, I don't check data_handler != NULL...
Hi. I am using nrf52840 with Softdevice 16.0.0.
I set the maximum size to 247 bytes. But I probably only need 68 bytes per packet.
Should I reduce my MTU size to 71 or...
Hi everybody!
I'm currently working on some firmware updates for a motion sensor. The code was originally developed with SDK15.0. The setup is as following:
NRF52840...
Hi,
I was trying with the aws_fota sample, I follow the instruction here and download the app_update.bin with no problem. After it shows completed in 100%, device reboot...
Hi,
I am measuring the time taken between an ANT application sending a message, and a receiving ANT application generating an EVENT_RX. This time is being measured using...
Hi,
my environment:
nrf5340 dk
nrf connect sdk - 1.5.0 version
segger studio IDE
we need a provisioner to add node into the BLE mesh. As per my knowledge, we...
Hi,
I have a few questions about how the peer list works. (using S132 v 7.0.1 and SDK version 16)
How or when are peers added to the peer list of the Central? Are they...
Hi Experts, I have a short quastion, what is the minimal RX-RX turnaround time of nRF5340? Unfortunately this parameter is not available in the specification any more. For...
Hi , i try to translate the arduino library using this URL github.com/.../src
to manipulate the spo2 oxygen concentrator value using the max30105 sensor I try to configure...
When I set tx_power and paired with the following microcontrollers, the power consumption of the 4dbm setting became larger than that of the 0dbm setting. Is this an effect...
Hi,
I am currently working on SDK 15.2.0 on my NRF52840 DK to program a bootloader that can do DFUs over SPI. I have been following the protocol found in this link . I have...
