Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello,
I want to send data via Bluetooth Serial as well as USB CDC Serial and currently, I am getting data rates up to 3.2KB/s on a Windows Laptop. I read this https://devzone...
Hi Community,
Facing the RF functionality issue on nRF52833 on our custom board.
Our board is functioning well with nRF52840, then it failed after migration to nRF52833...
Hello,
I am searching for nRF52 Flash memory mapping. I got some memory map from info-center but for me, it's not working.
The application Starting address is wrong in...
I couldn't launch FOTA upgrade over Bluetooth for nRF5340 PDK. I followed this guide developer.nordicsemi.com/.../ug_nrf5340.html to fulfil FOTA upgrade for nRF5340 PDK. I...
Hello,
My BLE peripheral device based on BLE uart example with nrf52832 has an issue.
My device is paired with central device and I turned off the central. My device started...
Any one tested with Strontium micro HCSD card?
I followed the the suggestions like BUFFERS=8 AND config_gpio=y.
I am getting the error Storage init ERROR!
GPIO Pins...
I am merging interactive command and buttonless dfu base on https://www.u-blox.com/sites/default/files/Add-NordicSemiconductorDFU-to-SDKexample_AppNote_UBX-19050198.pdf
...
I just recently got both nRF51422 and nRF52844 DK. However, when I tried to connect through J-LINK, the error message popped up: No emulators connected via USB. Do you want...
Hello,
I built a network of 3 parts. Each has a PCA10059 nRF52840 dongle.
Raspberry Pi 3B+ Border Router using the image from 4.1 SDK. This has the NCP
2X Full Thread...
Hi Everyone,
I am working on nrf52832, I am using sdk15.0.0 ble_peripheral /ble_app_beacon as reference.
I am not understood properly uesd for this function static void...
We just received our latest custom nRF52840 board and have found that there seems to be some issue with PO.19. We have verified that the P0.19 is not working on multiple boards...
Hi
Im using the NRF9160 DK
I have got the Asset tracker working, can modify the code, runs with nrfCloud, beauty
Just followed the docs
But then, I want to...
I have to stream packets from an nrf52 to an nrf24 at a 30 kHz rate using ESB. But when I try to do this, the receiver only receives some of the packets. I don't believe the...
