Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi,
Iam working on a nrf52840 and trying to achieve data flow from BLE device using NUS and transfer this data through UART.Uart is configured as (TX:P1.01,RX:P1.02).Iam...
I am using an nRF52 dev kit. I have loaded the pca_app_hts_pca10040_s132 example into the board. I only added these lines of code
nrf_gpio_cfg_output(ARDUINO_9_PIN); nrf_gpio_cfg_output...
Hi,
There are several new drivers under "nRF5_SDK_15.0.0_a53641a\components\drivers_ext\", but no example now.
I have setup the HTS221 driver and it works. I turn to...
I'm using nRF52-DK, and following the quidelines from devzone.nordicsemi.com/.../getting-started-with-nordics-secure-dfu-bootloader . I'm using the prebuild "blinky_pca10040...
Im trying to interface nRF52DK to Custome build acceleration sensor.
I want to use I2C communication. Are the pin connections mentioned below sufficient?
...
The buttonless_dfu_sdh_state_observer in this example is shutting down the cpu when the softdevice is disabled using an observer.
I'm not sure why this is necessary...
Hi everyone,
I have a project written in C++ for nRF52 series using the SDK 15.3.
If I use Keil and uVIsion, the project compiles and works great. With the same source...
I am using nRF52832, And SDK 15.3, the ble_app_blinky project,
a. if i have installed only the latest version of Device family 8.29.0 , when i try to build the project,...
Setup and goal: I'm developing an BLE central app and would like to use scan address filtering to find a specific device. I enabled the filter and provided a hard-coded BD...
Hello,
I successfully downloaded SAADC SDK example in the peripheral folder. The hardware setup is as below ,
The pin configuration for this is as below
...
I tried implementing
https://github.com/andenore/NordicSnippets/blob/master/examples/temp/main.c
But i get 2.6V without connecting any of the Analog pins.
Exactly...
I have attached an Arduino INO file that I wrote early on in a project. It runs a probe. It is an amazingly simple probe but especially important. I am making a simple opacity...
Hi Team,
I planning to use vibration motor with nrf52832.
vibration motor will give maximum buzz on 20.3KHz(50 duty cycle).
So my question is
- Can I achieve 20...
Hello I would like to use the extended advertinsing packets from Blutooth V5 as used in the "ble_app_rscs" example. My problem is that I can't connect via the extended advertinsing...
