Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi,
I am working on a product based around an nRF52832 (SDK 15.3, S112 v6.1).
I am using the Secure Bootloader and I have a script that is used to merge hex files and...
Hi,
I'm trying to write multiple compile time constants into the UICR (from the boot loader project). Currently I'm writing the boot loader addresses (start address &...
I want to update NCP application in the field. NCP is attached as USB device on Raspberry pi which act as border router.
I am using open bootloader ( pca10059_usb ) and...
Hello.
We are currently developing PCB design of smartwatch with RF Nordic nRF24 chip, Johanson small ceramic antenna (P/N 2450AT42B100), and capacitive Touch Switch (AT42Q1012...
I am using asset_tracker as the basic program and basically it is running fine and sending data to the RF connect web page.
However approximately every 30 minutes I get...
I am looking for a simple example for I2C write. The TWI sensor example is not clear.
It would be great to have an example like the basic SPI example
i.e.
How to init...
Hi, My company is interested in doing bluetooth beacon location tracking of android devices for a VR project. I notice we can easily purchase bluetooth 5 beacons on amazon...
Hi,
I am trying to migrate my project file from Keil 5 to Segger Embedded Studio (SES).
After porting all my source code and configuration files, SES is able to compile...
Hello,
I want "nrfutil" CLI tool (To perform DFU OTA of BLE) for one of my device which is based on i.MX6ULL ARM based processor 32bit.
I found that using "pip install...
Hi,
I am using nrf52840 chip, there is Thread and iot coap library, and movement sensor. When sensor detect move, pin call interruption and send coap message.
Voltage...
Hi all, Within my application I've followed the example/fstorage to the letter however upon requesting a flash write to the s112 the nrf_fstorage_is_busy() function loops...
Hi,
I am working with nRF PCA10056 evaluation board and using SDK 15.2.0. I am using nRF52840 as a central scanner, where it will scan broadcast data from beacons.
I want...
Hello,
I'm having problems with resuming usbdevice from susspend state. I'm working on SDK 15.2 with SD140 (6.1.0). on custom board with nRF52840 IC rev. 2.
My application...
Hi, the power LED no longer turns on on my nRF52840 DK board. The board is still advertising when it is connected to a power source and I am able to connect to it with a mobile...
