Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
I'm trying to mimic a fully functional zigbee color light bulb using the nRF52840 dongle.
Starting with the NRF5 Zigbee example light_bulb (examples/zigbee/light_control...
I apologize if this question is stupid
I want to read data in p_adv_report. I use the command NRF_LOG_INFO ("name =% x ", * p_adv_report-> data.p_data); but it's meaningless...
I am trying to use I2C (TWI) to communicate between my custom nRF52811 board with an Arduino. Currently my program hangs at the while (m_xfer_done == false); loop as m_xfer_done...
Hi Team,
We wanted to verify Sleep current numbers for nRF52833 SoC based custom development kit.
Is there any readily available firmware to verify these numbers?
...
I'm teaching a course, using the nRF52840-DK board as the lab platform.
Students download Segger Embedded Studio and compile the "Hello World" project from the 'nRF Samples...
Hi,
I have built a prototype that has two SPI slave devices connected to it and it works perfectly. I have now tried to add an SPI SD card aswell by following the FatFS...
Hi,
I'm now using nRF52833 DK to do the AoA test. I achieved the IQ sampling for a single antenna, but when I tried to switch between multiple antennas, the IQ results seems...
Hello!
My problem is that I am getting duplicates of the ACK packets I send from my PRX device to my PTX device.
To debug this problem, I configured my PTX to continuously...
Hi Devzone:
Is there a way to designate one ram block exclusively for radio use? The reason I'd like to know is the following:
Under nRF52833 AHB multilayer section, there...
I need a specific extended panid. Refer to the CLI example and add the following program:
Through the log, the extended panid returned by the device is 0000000000000000...
Hi,
I am developing an application with to 7 transmitters (peripheral) and one receiver (central = nrf52DK), all NRF52832.
I have 1 question and one problem to solved...
Hello,
# Issue I'm using a wrapper function for logging, in which you can set callbacks, which get passed the format string, and the va_list of arguments.
I'd like to...
https://community.platformio.org/t/platformio-plus-goes-open-source-improving-embedded-development-community-worldwide/8240
Hi will this means that we can expect to see...
