There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi,
I was actually trying out Nordic mesh topology and wanted to tryout the example programs.
SDK: nRF5_SDK_15.0.0_a53641a
mesh: nrf5_SDK_for_Mesh_v2.2.0_src
IDE:...
Hi Everyone
I am using
SDK 15.0
Segger Embedded Studio
nrf52840 on a custom PCB.
Softdevice s140.
FreeRTOS.
My requirement is , on the press of a button , the...
In the news today (26 Oct 2018):
http://www.eenewsembedded.com/news/embedded-studio-410-arm?news_id=111432
Will this work with current Nordic SDKs, or should we wait...
I am using FreeRTOS (sdk 15.2) configured to use RTC for the tick source and systick timer for the system. I am trying to put the device in a low power mode. I have tried...
Hi,
I use Iphone to scan for arround ble package.
The beacon is configured broadcasting every 200ms (I think all 3 channels 37, 38, 39 is default to broadcast signal in...
Hello,
I have a secure bootloader and an application on nRF52840 with SD 15.2.
I try to add watchdog support in application based on watchdog exemple but if i remove feed...
Hi,
i'm actually working for interface the nRF52 with the STM32. Actually i completed the part where the STM32 send some data and the nRF52 recive it.
Now i need to do...
Hello,
I am a beginner with Nordic semiconductor. I downloaded SDK v15.0.0 and used some of the examples and it worked perfectly for me.
My project uses different modules...
Wiring diagram
Testing process，The product will automatically disconnect. But it can connect again.
After setting the voltage to 1.8V in the voltage Reguator,...
This time I am trying to run Wireless UART Example but it seems that it does not work.
After I flashed dev board no LED were turned ON or flashing but web site says:
LED...
Hi!
Is there an example to extend the Bluetooth MTU size to more than 20 bytes together with SDK 15.2?
I found only examples with older versions.
Thank you in advance...
Hello
I'm wondering if it is possible to upgrade over-the-air from SDK11 to SDK15.
I know already that using the example bootloader from SDK11 will not work because the...
Setup: nRF5_SDK_15.2.0_9412b96 / s132_nrf52_6.1.0_softdevice / nrf52832
I tried to make a multilink nus central (PCA10040) with 2 peripherals (PCA10028) connected to it...
Hi, I would like to send data from nRF52840 Dongle to Raspberry Pi 3 through USB-UART. I programmed the ble_app_uart_c example found in SDK 15.2 and I connected that to my...
