Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
I have been using a Chinese debugger ARM v9 which supports JTAG+SWD to debug my nrf52840dongle so that I can upload my custom bootloader with my code in it using SWD pins...
Hello,
we have produced 10 Boards with nRF9151. Unfortunately, 3 device shows a false behavior. We cannot connect over SWD an they have a larger power consumption (whole...
I want to implement FOTA Update for a nrf5340 based board by using nrfConnect SDK v2.9.0 with zephyr and mcuboot. The board has a MX25R6435F external flash (same as the nrf5340dk...
Hello,
I am trying to run a ztest integration example I found under this one here: https://github.com/zephyrproject-rtos/zephyr/tree/main/samples/subsys/testsuite/integration...
Hi,
I am sending out same payload through ADV packet and BLE connection packet, I notice the ADV consume more power compared to connection one,which is quite strange.
...
Hi, I am using NRF connect sdk 2.6.1 and I am wondering what is the best way to run crypto operations when using TFM profile type minimal and building for nrf9160_ns. TFM_PROFILE_TYPE_NOT_SET...
I want to measure the current consumption on the DK with an Amperemeter. For that i have this setup:
Please excuse my terrible drawing skills. Im basically powering...
I am using NRF52810 as a beacon tag.
I want to apply AOA technology to this tag, is it possible?
I'm confused because the nrf52810 says it supports BLE 5.2.
Hi,
I'm experiencing memory constraints while using the nRF52811 with the SoftDevice S112, as it takes up a significant portion of the available memory. Is there a lightweight...
Hi,
We developed an application on the nRF52833 and are now porting it to the nRF54L15. As part of this process, I'm integrating an external RTC via I2C on the nRF54L15DK...
After purchasing the PPK2, I connected the Fluke287 and PPK2 Ampere meter in series to check whether the measured values matched the Fluke equipment.
The Fluke287 consistently...
Hi
I have run nrf5340 WiFi shell project in ncs2.9.0, everything ok if use Logging UART0 for cmmands(wifi scan/wifi status/ wifi connect.....etc)
now I need to use...
Hello all,
I have slightly modified the coap_client sample from the SDK such that the main function is being called on certain actions from another program. I'm getting...
I use the gpio8 interrupt to detect whether the SD card is inserted. When a falling edge is generated, it means that the SD card is inserted. But I found that sometimes, the...
