Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
I would like to set a gpio pin on Radio RX Ready and clear it on Radio Disable all via PPI. Below is my code. I only get the pin to change levels when the OUT task polarity...
We are looking into the following link for the softdevice S112 API documentation however we are getting Error Code 404.
Technical Documentation (nordicsemi.com)
Can...
Hi ,
I want to enable encryption in Bluetooth communication for a proof of concept.
I have Wi-Fi Provisioning example and in that while sending the wi-fi password ,...
Hello,
We are using nPM1300 in our project.
I would like to configure it to the maximum possible discharge current limit, as there are inrush currents in the board.
...
Hello, I have a couple of questions concerning the nrf52840 dongle
1. Is the dongle supported in the nrf connect sdk? I see that the board is within the build boards,...
Hi Sir
I am using an example from NCS 2.6.0 and want to modify it to use ADC channel 6 (P0.30) to read voltage values, but I am unable to get the correct values. (When I...
Hi, I have a custom board connected with DK and i was able to program it and test some simple codes. I need to test this TWI example on my board. I uploaded it but i am not...
I am currently developing with the nRF52832 using the nRF5 SDK 14.2 and need to proceed with AES-128 encryption.
However, I cannot find the CDC (Cipher Block Chaining) library...
I'm using nRF Connect SDK version 2.3.0 nrf52840, and external flash - W25Q256JVEIQ. I believe I'm running the chip at 80MHz (rated for 133), with the qspi chip and partition...
OS: Windows
Name: nRF Connect for VS Code Version: 2023.11.301
Found an issue with saving the preset file (Save configuration as preset) when project is located on a...
I'm using an nRF52840 and SDK 15.2 (although I can go to hardware directly if required).
What I want to do is to set a pin as an output with a normal drive run high on...
Hi,
Today I'm trying to run a Thread application on an nRF5340, using the secure environment (not ns). Building the firmware as ns is fine and works as expected, but when...
Hi,
I tried running the \zephyr\samples\bluetooth\periodic_adv program as a host-only application on the nrf52840 development board, with the controller using an nrf52832...
We are working on an idea for a protocol with very low latency events for multiple devices.
For this we would like to be able to transmit a packet only when no other transmitter...
Hello Nordic,
We are currently working on a project that involves communication between Main MCU and a Nordic BLE. From the documents i found that, we can use SPI or UART...
