hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
One of my customers currently has a requirement similar to the one discussed in this ticket:
In their product, the main controller is a BES2610, and the Bluetooth functionality...
Hi
According I2C standard, there is a requirement regarding falling speed of SCL/SDA which is > 20*1.8/5.5=6.54ns, and our measurement result of Tf on SCL is 5.732ns.
...
Hi
I am using the nRF7002 DK with NCS 2.7, based on the sample project `nrf70-wifi-ble-image-transfer-demo`. I modified the code to embed a fixed image as a header file...
Hi
In nRF5340 datasheet I2C frequency only have 4 selection as below
But when ask your AI, he response below
Important errata at 400 kHz
For all nRF5340 revisions...
I would like to trigger a hard reset when valid voltage is first detected on VBUS. How could I do this with no or minimal external components and without a complementary MCU...
We are using the nRF54L15 SoC with FOTA functionality. We have enabled secure FOTA by signing the firmware image and provisioning the public key into the SoC’s KMU. For production...
I'm running the subrating sample (ncs\v3.1.1\nrf\samples\bluetooth\subrating) on two nRF54L15-DK boards.
I'm puzzled by something I can see through my protocol analyzer...
Hi,
I’m working on a distributed testing pipeline where tests are built on one machine, but executed on a separate, lightweight container that does not contain the full...
Hello Nordic Team and Community,
I'm working on a fully automated Zephyr RTOS development environment on Raspberry Pi (Debian Bookworm) targeted at the nRF52840 Dongle....
Hello,
Is it possible to get logs (RTT) from an application started by a bootloader? As of now I don't get anything after the bootloader has jumped to the application start...
While running the BLE HCI USB ( bluetooth_hci_usb ) sample in Raw mode on an nRF52840 board, we observe a bus fault under specific conditions. The fault occurs when the device...
Hello everybody,
I am a research assistant at a university , responsible for maintaining and porting existing student lab exercises from the legacy nRF5 SDK to the nRF Connect...
Background:
My project is using the nrf54L15 with the 48 pin package. I'm using vscode with v3.2.0. The QFN48 package has the following pins bonded from the silicon to the...
I am trying to receive extended advertising from a device on nRF52832 .
I have made the following changes:
sdk_config
# define NRF_BLE_SCAN_BUFFER BLE_GAP_SCAN_BUFFER_EXTENDED_MIN...
