Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
I'm getting the warning about CONFIG_BT_CTLR, but I've gone through and changed to HAS_BT_CTLR. I do have the following:
# Maximum Transmission Unit config
CONFIG_BT_GATT_AUTO_UPDATE_MTU...
Hi,
I would like to know if nPM1300 supports an input voltage of 4V for Vbus. According to the datasheet, the recommended operating condition for Vbus is from 4V to 5.5V...
It seems BLE stops advertising after the first connection. Is this expected behavior? Should I restart advertising in my "connected" connection callback?
prj.conf:
main...
We have firmware that works great on the nRF7002-DK board, but now that we have our own board with a Fanstel Wi-Fi module it appears that the Wi-Fi hardware is not responding...
Hi, Goal: Send a firmware update from nrf5340 to another nrf5340 over BLE I found the following sample and a lot of support tickets talking about this sample but I am unable...
Does Zephyr support automatic reconnection of the Wi-Fi if a connection is lost? I can't find any documentation on this, or code examples. It seems like every example connects...
In my application we have an nRF514L configured as an SPI target. Page 830 of the nRF54L datasheet (version 0.8, dated December 2024) documents that the SPIS peripheral requires...
Hi!
With SDK15, I figured that is possible to change the advertisement content on the fly by overwriting the content of `adv_data.adv_data.p_data` and updating `adv_data...
I am using nrf5340 in my project. We had to replace flash memory but need a replacement with the same layout. So I am currently looking at w25q01jvzeim or w25q01jvzeiq . The...
I have a characteristic whose value is an array of char, which can from 1 to 20 bytes long. Using SDK17 I can set a vlen attribute and use the function update_characteristic...
Project based on NUS Central example.
Application is to connect to multiple peripherals concurrently running a custom service and subscribe to Notifications on a characteristic...
I'm using Nrf connect for Mobile to test my BLE firmware. I noticed that when trying to write more than 20 bytes to a characteristic, nothing gets logged which means my write...
Good day,
I am trying to program the nRF Sniiffer firmware to my nRF52840 dongle using the "nrfutil device program" command.
According to the User Guide v3.2 for the nRF...
Hello,
We are in the final stages of development with a board that combines the nRF5340 with the nRF7002. This board also requires native USB support and we are routing...
