Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hello,
I used SDK15.3
Android phone and iOS phone is master
nRF52811 module is slave
It's said that the phone can't set conn international（Android、iOS）
But slave...
Hi,
i am working on "nrf52dk" . i want to use nfc pin as gpio.
what i did is
NRF_UICR->NFCPINS = 0<<0;
CONFIG_NFCT_PINS_AS_GPIOS included in preprocessor definations...
Dear Nordic,
I'm doing network registration test with nRF9160 DK in CMW500 test network environment.
I've set CMW500 configuration up as described at "https://devzone...
For a Non-RTOS application, take ble_app_blinky for example, the application is coded by us while SD is provided by Nordic.
My understanding is that the SD is running as...
Hello, All
I saw this description in the Bluetooth 5 Go Faster. Go Further document：
Advertising sets have an ID which is used to indicate which set a given packet belongs...
Setup:
Module: nRF51822.
SDK version:nRF5_SDK_11.0.0_89a8197.
Example: ble_app_uart.
Softdevice: S130.
I use ble_nus_string_send on the BLE_GAP_EVT_ADV_REPORT...
I'm following the NCS tutorials. I'm targeting the 52840 on the 9160DK board. I'm using SES with NCS1.6.
I'm able to get the hello world to run and the message is out on...
Hello,
we are developing a customer product based on the nRF9160 and Nordic's NCS v1.4.2 where we need to send battery test data every 30s (~ 1kB, PUT method). The communication...
Hi:
I am working on a stereo microphone application using the NRF52840. I would like to have the 2 microphones output 16K samples per second (8K samples each for left and...
Hi,
I am using nRF52840 on custom board. I am trying to configure SPI pins, but I am not getting anything on the clock pin. I can see the chip select pin going low and...
I have a custom board with a nRF52805 based module from Minew and I'm trying to do a OTA DFU but I can't quite understand how it works.
This is what I do. For info, I...
Hello,
I am working on product based on the NRF52. It has an external EEPROME wired via I2C bus (no external pullups). I see an extra 300uA ish current consumption after...
