why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Sorry this is an urgent request and we could not find much information on the internet about this module. We have a tight schedule so it might be a good idea to post here...
Hi, Hope your are well, i am currently in the final part of my project where i am SPI Gyroscope float data from one nordic nrf52dk (S132) to another such that i can analyize...
I am running read str 0x3e000 12 via UART line but there is nothing which gets printed on the terminal.
Even if i write some hex value to a particular flash memory location...
Hi there,
I have set up the nRF2427 with the nRFgo Starter Kit motherboard (nRF6700). The motherboard is recognized and I have all of the 2.4GHz options available. I would...
Hello,
I am working on the nrf52832 board with SDK16.
I am using a custom BLE example.
My TWI and BLE code work ok individually but when I integrate them it does not...
Using S132 v7.2, I'm getting a hard fault at PC 0x00015810 (I see the flag set in SEGGER, and the console outputs a SOFTDEVICE ASSERT FAILED error) that I'm working on manually...
Hi,
The 'nRF Connect' SDK (v1.4.99-dev1) sample OpenThread CLI is programmed to receive 'ot' commands from UART console. When configured with multi-protocol support, the...
Hello,
I have a problem that sometimes the supl_client_session() function halts the system by not finishing and ending the session while getting the timeout expired SUPL...
Hi
I can't find fwid for sd132 7.2
|s132_nrf52_5.0.0|0x9D| |s132_nrf52_5.1.0|0xA5| |s132_nrf52_6.0.0|0xA8| |s132_nrf52_6.1.0|0xAF| |s132_nrf52_6.1.1|0xB7| |s132_nrf52_7...
Hi there,
Our team is developing an application based on the nRF5340-DK - we are developing on the DK while our hardware is in transit. Our schematic largely follows the...
Hello, I use the internal crystal, the application in my board runs normally and it shows the board is in fast advertising state. However, I can't find bluetooth signal through...
I'm running the Zephyr hci_usb sample on a nRF52833DK to see if I can use it as a Bluetooth dongle on my Ubuntu dev machine. It appears as /dev/ttyACM0, so:
sudo btmon ...
Dear Nordic,
I have a BLE mesh product that is in pre-production. The mesh gateway is composed of an nRF9160 and nRF52840 with a UART link connecting them. The nRF52840...
Hi,
I have updated nRF Mesh to 3.1.0 version (iOS), but I can not see any field for reading sensor values. I set app key and publish/subscribe addresses for sensor server...
Disclosure. I am new to firmware develoment. My experience is in cloud development.
I just bought a Thingy91. I registered online using nRF Cloud. The modem communicates...
