I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
SDK: 17.0.0
Hardware: E-Byte E73-2G4M04S1B module
Chipset: NRF52832 QFAA QFN48
Running the hids examples, I noticed that the hids_mouse example will go from Fast Adv...
Do I need to carry out ANSI C63.27 regulatory test for coexistence of wireless communication that share the 2.45GHz band if we designed a custom PCB BLE antenna for NRF52840...
Hi,
I have the nRFgo Starter Kit with the radio module (nRF2427LE1) attached. First, does the radio module not have a bootloader already downloaded to it? Next, when I...
Dear Support Team.
We want to support secure DFU on mobile and desktop platforms. Do you have any documentation to implement this on Mac OSX and Windows?
Its an open...
Hi, is there any LE audio sample for NRF5340?
I know the upper layer protocol is under developing on Bluetooth SIG, but is there any possible way to direct use the HCI command...
Hi
I'm developing with nRF52832.
I am using Segger Enbed Studio as a development tool.
When you download a program from Segger, Segger does reset once, and I wonder...
Hi,
I want to run QSPI application example on my nRF52840DK (PCA10056) board with logs seen via UART. I successfully uploaded QSPI bootloader example and Blinky SysTick...
Hello,
I'm developing an BLE application with NCS where I want to be able to change the BLE device name during runtime. Therefore I enabled CONFIG_BT_DEVICE_NAME_DYNAMIC...
Now we development a switch and use it control the light. When i push switch close the light, there was still a faint light. Then i found when NVIC_SetPendingIRQ(EVENT_IRQn...
What I intended was to write x'700' to x'10001080' i.e. NRF_UICR->CUSTOMER[0] !
When ran my application, which outputs NRF_UICR->CUSTOMER[0] to the log, I was very confused...
In firmware I can read the programmed UICR serial number as follows: -
uint32_t serial;
memcpy(&serial, (uint32_t*)0x10001080, 4);
Is it possible to program the UICR...
The peripheral_lbs sample on the nRF5340 with the nRFConnect v1.5.0 builds fine and the merged.hex file downloads fine, but it does not appear to be running, no blinking light...
I have a program that recieves data from another chip over Serial. It sends 2048 blocks of data which than get transmitted to our C2 over mqtt. Problem is that afther 12/14...
Hi,
I am trying to receive and send data from an android device to an nrf52840 device with USB CDC. I have already installed the application using this link https://jimmywongiot...
