hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
when I use central and Peripheral all concerned, Eight Peripheral connected to the central 。when I'll connect my phone to the central Peripheral . Device Error
Here's the...
Hello,
I am using a nrf52 DK in an educational context.
For this reason, I am not using the SDK, but implement basic features on a lower level.
I used the implementation...
I would like to confirm that the temperature measurement is sent from the end-device to the coordinator using the example zigbee temperature sensor.
I'm looking at Testing...
With the introduction of mesh_config_file_clear() in 4.2.0 the behaviour of mesh_config_clear() was changed such that only a subset of all the file ids handled by the Mesh...
How to add new i2c based sensor device to ncs\v1.3.0\zephyr\drivers\sensor.
Can you suggest any tutorial to do so as i want to use sensor subsystem which in turn uses i2c...
I have produced ~ 15 different custom board variations that all use the nRF52810-CAAA. They all have the same reference schematic, and use 4 programming pins (V, G, SWDIO...
Hello,
I have an application that uses the SPI- and the TWI-Manager:
But the application throws the error code 17 when the program tries to initialize the TWI-Manager...
Please see Nordic nRF5x Bluetooth DFU upgrade firmware process.
If device is powered off at the step "Copy new firmware" and powered on again device goes into bricked...
I have a peripheral and central that bond with each other. Now until I had peripheral stop advertising on first connection, it was all fine. Now this peripheral needs to connect...
Hi,
On my nRF52840 DK PCA10056 Arduino connector I have mounted some external ST board.
With ST through Arduino interface I am communicating something with nRF52840. ...
Do you know how to handle a write event from its (such as char) descriptor value in a customized BLE service ?
Here is the code of my on_write function :
Setup : nRF52840...
Hello,
I am working with the nrf52832, softdevice s132, and I have configured my own service using this online tutorial :
https://devzone.nordicsemi.com/nordic/short...
hi
im use the command line of nrfutil to ota the nrf52840' firmware.but now i want to develop a soft to ota the device without the environment of python.but i dont kown...
Hello,
I'm measuring the value of a lithium battery (3.7V 110mAh). I used SAADC to measure the battery power and it seems to be quite accurate. The charge IC also attempts...
