hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello
Using PCA10040 dev board,
Building with SDK 16, & S112 - using ses
Running ..\examples\dfu\secure_bootloader\pca10040_uart_debug
Using nrfutil to download...
When running the "nrfjprog --recover --log" command, on a Windows 10 pc in CMD, this is the output that I get. I am unsure what steps I need to take from here.
Any help...
Hi,
In my application I have a requirement to send notifications to mobile on triggering particular Interrupts as well as particular events.I have created a customised notification...
Supported tx_power values: -40dBm, -20dBm, -16dBm, -12dBm, -8dBm, -4dBm, 0dBm, +3dBm and +4dBm.
What is difference in the behavior of nrf 52832 chip for these different...
We're developing Bluetooth tags that we would like to operate at both 1Mbps and coded (long range). From what I've read and seen from the Nordic testing, specifically "Testing...
I modified the gpio interrupt on the asset_tracker example of ncs v1.2, modified the following, and the interrupt didn't work: Where is available should be modified.
I set...
Dear Friend，
Based on nRF52832, mesh3.1, port ble dfu to mesh project, Android dfu application is based 'no.nordicsemi.android:dfu:1.10.1'; Call the following program: ...
My setup: custom board using nRF52840, Segger Embedded Studio 3.52, nRF5_SDK_for_Thread_and_Zigbee_v4
I used a couple of your projects as a starting point for my code. Specifically...
Hi,
In my proejct, I am using WFE(); in some while loops because of core low power mode.
For example, waiting for time_out flags like codes below.
I am wondering if...
Hi All,
I'm new to the nordic product. We previous using TIcc2642 as development board. And we would like to test our application over different hardware. Is there any...
Im using CUstom BLE tutorial example and it works fine. But i just wanted to know, in which section is the text data for logging occuring. Ex: "notfication received from ...
Hi community !
I want to know if a code works on nRF52840 DK PCA10056 will work on nRF52840 PCA10059 ? On both, i will never use physical input (button led or gpio) i'm...
Hello expert,
I just jump from TI. Could anyone tell me if nordic has any chipset like TI CC1310 which supports direct access to the receiver I/Q quadrature samples?
...
The Thingy91 GPS system sensitivity is terrible. Getting the GPS to lock on takes forever, and many times doesn't lock on at all, and if it does lock loses the connection...
