why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
There is a potential for the NRF_MESH_ASSERT(m_reliable.next_timeout_index < ACCESS_RELIABLE_TRANSFER_COUNT) to fire on line 170 of access_reliable.c if the following conditions...
Hello,
I am trying to install the pc-ble-driver-py for my buildroot arm-board.
After some struggle I was able to compile the pc-ble-driver for it, however the python tool...
Hi guys,
I am working on my project and until now I enabled the device to measure the voltage and get the sensor data from the temperature sensor which I need now to send...
Hello,
We have been using FDS in our nrf52832 based product. Recently we had a need to port application to nrf52810. It required some flash memory optimization. Fortunate...
Documentation states “When a connection is created it will inherit the transmit power from the initiator or advertiser leading to the connection.” In my BLE event handler...
Hi,
SDK16
I'm using ble_cus.c to define custom BLE service.
In the ble_cus.h file the definition of the UUID is
#define CUSTOM_SERVICE_UUID_BASE {0xBC, 0x8A, 0xBF...
Using just the nRF Connect SDK, I cannot get a push button to interrupt the NET CPU on the nRF5340DK.
I have the following code on the APP CPU:
nrf_gpio_pin_mcu_select...
L2CAP connection oriented channels can be used to transfer frames of up to 65533 bytes. L2CAP is a record oriented protocol. When receiving L2CAP data, using the softdevice...
I have purchased eval kit and entered bootloader mode by pressing BOOT/RESET button while powering up the device but haven't put any file but now when i power up the device...
Hi,
We are in a stage where we want to perform certification of a product and are now looking into an application that can be used to this end. The board is using SDK 15...
Hi,
I've bought a nRF52840-DK kit to evaluate a Nordic BLE SOC (we are interested in using the nRF52811). I've installed SEGGER Embedded Studio 4.52, and obtained a Nordic...
Hello, I am I'm a Beginner at developing NRF 51822. My Development Environment sdk : 12.3 IDE: KEIL v5 SoftDevices : s130
I am developing using the example of 'ble_app_uart...
Hi everyone,
I am trying to understand the Memory layout of nRF52840 SOC in order to apply RAM retention into specific section. Looking the memory layout at pg 21 of the...
