Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
I have successfully added an event handler for managing if a write operation is performed on a characteristic, but how can I know that which characteristic has been written...
Hello,
This example I got it working with nrf toolbox app, but I was wondering if this should work also with a win7 PC. https://infocenter.nordicsemi.com/topic/com.nordic...
Hi,
in NB-IOT the UE should make a Traffic Area Update TAU when timer T3412 expires. I have a project based on the UDP_with _PSM sample. When I configure the PSM timer to...
Dear All,
I am trying to minimize the current consumption of my device. I am using several peripherals, such as UART, I2C and ADC.
When I run a very simple sample...
I am working on a line of products that use the same Microcontroller and softdevice so the same QDID. Most of them work with a module and one has the same chip mounted directly...
Hi, I'm using this post to upgrade from SDK 11.0 to SDK 15.3.
All goes well, until I uploaded an application: then I get a hardfault somewhere at fds_init().
I found...
When I start nRF Connect v3.2.0 the first window starts as normal, but when I click on Open Bluetooth Low Energy the nRF Connect v3.2.0 - Bluetooth Low Energy window is blank...
How can application code interrogate the SD140 to identify which version (such as 6.0.0) is running.
We pre-flash (before SMT) our nRF52840 with a bootloader and SD140,...
Hi ,
What does the handle parameter in status_handle(access_model_handle_t handle, const access_message_rx_t * p_rx_msg, void * p_args)function (generic_onoff_client.c)...
Hi all,
I am trying to reduce the connection time between each connection to the minimal posible
Connect -->Transfer data -- Disconnect
I am facing two options...
Hi,
I want to make simple software that runs on PCA10056 using SEGGER and SDK. To learn how to use SEGGER, I copied exsamples / template_project and tried to imitate blinky...
Hello guys, i'm using nRF52832-DK with S132_v3.1.0 and SDK v12.2.0.
When other BLE device write some value to my characteristic, how do i know
that my characteristic...
Hello,
I am using a custom board that has a DSP and the Lairds BLE module BL651 that has nRF52810. I have written a simple program that sends a test data byte to the DSP...
