Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi,
I need to create a dynamic array to send a different number of bytes of data using TWI. Here is how I create an array:
When using the malloc function, I always get...
Hi
There was a problem using the external ADC AD7792 in a project with SoftDevice. The problem is that when the ADC is processed in a project with SoftDevice, the waiting...
We have implemented proprietary audio streaming on the nRF52. It reads Audio from a PDM mic and uses the timeslot feature of the BLE radio to send said audio to another BLE...
Hi:
I already updated the SDK to the first release version V1.0.0 and the unit works well with NB-IoT, UART and SPI. I'd like now to include real GPS data but I can't get...
Hello, I'm working on programming a cycle to measure the power consumption. I need to send a message and wait for a response for some time, then shut the modem off, no matter...
Hi,
We were planning to use a spectrum analyser in order to do the radio test on the nrf52-dk. Where should the analyzer be connected? Should it be connected to the J1...
Hello, I'm trying to test the UART example for nRF 9160 DK. To my understanding, any input sent through one of the ports should appear in the other one (from uart1 to uart0...
I would like to use PSM to save power consumption of nRF9160 LTE module. However, if I use PSM on the module, the module is dormant and not able to receive the command from...
Hi, this might be a trivial question but I'm struggling to find the solution. I want to configure the asset tracker application so that it works with real GPS data on the...
hello!
i am using my nrf52832 with s132 softdevice. basically the ble template with my services and charas.
i checked power consumption in sleep mode and observed something...
Adding a Network Coding Extension to CoAP for Large Resource Transfer
https://ieeexplore.ieee.org/document/7796871
Can I use this coding in your some SDK project?
...
Hi all,
I ned to test DTM in labview. In nRFgo Studio works fine, but I don't have any idea hoe to relize same test in labview. Could anyone help me please?
Thank you...
Hi,
I'm working on nrf9160 DK board version 0.8.5. I want to use analog pressure sensor and read data using GPIO input, however there is a little issue related to acceptable...
Hi,
I'm having issues maintain the connection to a MQTT server. I'm able to establish the connection, keeping this alive and pub/sub some massages, but after some time ...
