hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hello,
I am evalating the nRF9151-SMA-DK with a Monogoto SIM card that uses Skylo NTN connectivity.
I am able to reach the internet, since DNS resolution works:
...
I recently purchased an nRF51822-mKIT and I'm having great difficulties in getting it to talk to either a Windows 7 or a Windows 8 desktop PC, or a Ubuntu linux desktop PC...
Hi all,
Due to wrong pin assignment on my PCB I am currently bit banging a uart on two P2 pins using the FLPR core. The read bytes and bytes to send are communicated via...
Hi
I'm trying to drive a 75hc595-type shift register with a SPIM instance on the nrf54l15.
I connect MOSI to the shift register data input, CLK to the shift register clock...
Hello,
after a longer time, I wanted to use nRF Connect for Desktop again, to figure out what exactly my device under development is advertising. I upgraded to the latest...
Back in SDK 17 or so there were code samples for both the client and server side of the LED button service.
What happened to the client/central example when you migrated...
Hi,
While testing, I ran into multiple problems when measuring the current consumption with the PPK 2 on the nRF52833 dk.
For all measurements the Blinky + Bluetooth demo...
Description
I'm working on a battery-powered application where WiFi needs to be shut down between cloud sync intervals. I'm following the same pattern as the wifi/shutdown...
Hi,
working with nRF52840 with S140 v7.2.0, not sure about SDK version. VS Code + ARM GCC + LD Gold linker.
I changed stack and heap sizes via __HEAP_SIZE and __STACK_SIZE...
We are experiencing an issue with high current consumption when using the nPM1300 powered by a battery. In Hysteretic mode, the battery current draw measures 109 µA. However...
Hello Nordic Team,
We are currently working with the nRF54LM20B device and would like to understand whether Bluetooth Channel Sounding is supported on this SoC.
Specifically...
Hi：
What is the maximum number of targets that a DFU distributor can support for simultaneous upgrade, and what is the upper limit? I haven't found any detailed explanation...
I'm trying to put my code on a RAM/ROM diet and cut out any extra cruft so it will fit in an nRF52832. It used to fit with older SDKs, but not with the newest (v3.2.3).
...
Hello,
Is it possible to configure an nRF5340 to be both a Broadcast Sink and a Broadcast Source, but with the condition that only frames received by the Broadcast Sink...
Hello,
I am measuring RSSI values with nrf_modem_dect_phy_rssi(...) from the DECT PHY firmware.
The nrf_modem_dect_phy_rssi_event refers to positive values being saturated...
