When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi all,
I am facing issues when initializing and enabling the Softdevice after using the nrf_nvmc driver to erase and write flash pages. The project shall have the ability...
I am working with a MacBook Pro (El capitan) and the nRF51822 beacon and I need to measure the RSSI. I understand that the app nRF connect can do it, but the antenna on my...
Scenario is as follows:
NRF52 (SDK12.1, SD3.0) works in central and peripheral mode.
What happens is that on start we create a single shot timer with 4.2second to wait...
I write a function, It can read ok without BLE starting.
When I start the BLE , the function can not run.
So I think that , if I can use some function to stop the stop the...
Hi, all.
I tested ble_app_uart in example directory by PCA10040 board.
It works well.
printf ("UART Start!") in main.c works well. "UART Start" string cames out on putty...
Hello everybody,
I have a problem when I try initialize the ANCS service. The method ble_ancs_c_init(); from ble_ancs_c.h return the error NRF_ERROR_NO_MEM.
My configuration...
I flashed the nRF52 DK with the mbed bootloader developer.mbed.org/.../ but I'm having issues with the board. When I drag and drop the file which is a very basic blink program...
Hi,
I was trying to integrate a more simple version of the buttonless dfu example on my application. My first step was to get rid of the peer_manager and also the flash...
What is the use of of PCA10040 chip in NRF52 Development Kit(NRF52832 chipset). ?
Do I need a programmer to program NRF523832 in the DK, Can I just program it through USB...
Hello,
I asked a question after this old one : old one and I read other posts on the subject.
I wonder whether explained constraints may have changed or not since I am...
Hello,
I'am trying to do directed advertisement with NRF51822 (Smart Beacon Kit pca20006). I don't have any previous connection with peer, its address is hard-coded. The...
Hello:
I am writing a BLE profile involving several characteristics. One of the characteristics is an operation code (read/write) tunnel.
Each time a BLE central device...
This situation occured just in Android phone,iphone have not meet this situation.
A detailed description as follows:
After DFU used Android phone,connect again,notify...
Hi, I want to send data from arduino to nrf51dk which will then use uart service to send the data over bluetooth.
I want to use SPI communication between the two microcontrollers...
