Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
When I add an attribute with BLE_GAP_CONN_SEC_MODE_SET_OPEN I get a BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event when I try to read it.
I do not however get a BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST...
My application involves driving a digital-output (PDM) MEMS microphone at 1 -- 3.25 MHz with a clock generated on a GPIO.
devzone.nordicsemi.com/.../
The output of the...
Hi, I have a custom service with 3 characteristics and i've been attempting to send one of them as a notification so I can use it in the HRS sensor app by changing the UUIDs...
Hello,
I am working with the nRF51822 and S110 Softdevice. I have so far successfully created several examples of fairly complex Peripherals. Now I am trying to,
A)...
Hello,
If we use same hardware and antenna design of one of Nordic DV/EV kit, can we shorten bluetooth LE certification process?
I see Nordic points the following app...
Im trying to run the example blinky_example on BLENano (tried with gcc / nrf51822-sdk on linux and windows)
.hex from linux before merge : 8475 bytes
.hex from windows...
I'm looking at the downloads for the nRF51 DK which has the nRF51422 core. I'd like to put the s110 softdevice onto it, but I don't see a download for s110 on nrf51422, just...
Hello,
I am trying to use the s120\multilink_central example, using SDK v6.1 and S120 v2.0. The probleme is that I get a hardfault handler. I think that the probleme is...
Hi, I am using a nrf51822 with sdk 7.2.0 and s11o v7.1.0
I also have a imu ( mpu 6050 ) that gets accelerometer and gyroscope data.
How do I do continuous transmission...
Hi,
I am using the nRF51 Dongle and every time I send a command the pipeline goes into "Stall" condition. Using USBlyzer I can see that the command is sent but straight...
Hello,
I would like to build a device that looks for other beacons (not using a phone)... This device would simply look for other beacons near this device.
My questions...
I just tested putting the same firmware on two different nRF51822 s and inspected them with this test app .
They show two different UUID's.
I can find no macro...
Hello guys!
I'm experiencing some troubles trying to compile the blinky_rtx example for my new nrf51DK. The source is taken from the SDK7.2.0.
I'm under Linux and I...
I am brand new to nRF51 DK and I am struggling to figure out where to start. My goal is to periodically sample analog inputs and write them to SD card.
Can someone point...
