why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hello all, I'm currently developing some test FW for our custom hardware which include a nRF5340 and nRF7002, I made a small program to test the the different power supply...
We're trying out using devcontainers in WSL to develop Zephyr based software for our products. For flashing products from within the devcontainer we're connecting the corresponding...
Reference link: https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-9-bootloaders-and-dfu-fota/topic/exercise-1-dfu-over-uart/ I have an nRF54L15...
Hello everyone,
I'm working on a design using an nRF SoC and have a question about the correct way to handle I2C pull-up resistors in a mixed-voltage system.
My Setup...
Dear Nordic Support Team,
I’m encountering an issue during debugging where the code consistently hangs at line 360 in nrf_sdm.h , specifically at the following call:
...
Hi,
We are working with nRF52832. Over requirement is we need to transfer the file over BLE. We are using UART service (nus) to transfer file over BLE we getting maximum...
Hello,
I am working with a thingy9160 to connect to an MQTT broker using TLS.
I have run into an issue where the MQTT connection is disconnected with error code #XMQTTEVT...
Hi,
I have a nrf52833 with MCUBoot and BLE, I am using NCS v3.0.1.
I need also a custom NVS partition to store user data, so i create a data_partition for this purpose...
Hello,
I'm trying to build a Zephyr module that manages some features for a specific board (an SDK for that board). In it, I would like to enable the IPC devices in the...
I am testing data transfer from a microcontroller to a host PC using USB CDC ACM on the nRF5340. Right after powering on the microcontroller, only the first packet takes longer...
hi support team,
do we have any samples on how to show radio statues to gpio? when radio is on, gpio is set to high, and radio is off, gpio is set to low.
waht i can think...
Hi everyone,
I'm in the middle of a project and am starting to run out of available GPIOs.
To save a pin, I was wondering if it's possible to use a single GPIO (for example...
As a detour to getting DFU working for my existing project, based on nRF54L15, it was suggested in a previous ticket that the issue might be with my custom board folder, and...
Hello,
I would like to ask if it is possible to print the status of individual parts of memory on nRF7002-DK while the program is running? So far, I have managed to print...
