Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Somehow it seems the interface MCU of my PCA10040 DK got confused. I cannot use the JLINK to the nRF any more, and the JLINK drive (in Windows 10) does not show up. LD5 stays...
Hi,
1. I want to know the minimum delay time of BLE data transmission
2.How should this time be calculated
Thank you for all your assistance. Kind regards, Peter.Mi...
I want to modify the lte_ble_gateway app (nRF connect SDK 1.6.0) to connect with the nRF52DK advertising through the ble_app_uart (nRF 17.0.2) application. The lte_ble_gateway...
Hello Nordic Devzone,
I am currently attempting to generate 8mhz clock output to a gpio pin on the nrf5340dk. I have found previous posts about utilizing the gpiote, timer...
Dear Members,
How can I find the cause of
<error> app: Fatal error ?
I can't see an error code ?
Is it possible hardware error because voltage surge ? Can capacitor...
When I set NRF_LOG_ENABLED true, the RTT log can be output without any problem, however, the scanning or advertising activity stop immediately.
I found there is something...
Hi,
I am trying to find Get and set the RTC timer api inside Nordic SDK "nCS\v1.6.1\zephyr".
Could you please help me where I can get these api.
Thank You!!
I got up to this stage while trying to evaluate the module...
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrf91_dk_gsg%2FUG%2Fnrf91_DK_gsg%2Fintro.html
There...
Several place refer us to the SoftDevice Release Notes; eg
https://www.nordicsemi.com/eng/nordic/Products/nRF52832/S132-SD-v5/58987
http://infocenter.nordicsemi.com/topic...
Hi,
I have nRF52840 DK with nRFConnect SDK 1.6.99
Compiled and run on nRF52840 boards:
F:\_Develop\ConnectSDK\ncs\zephyr\samples\bluetooth\periodic_adv
F:\_Develop...
NRF_SDH_BLE_OBSERVER(m_ble_observer, APP_BLE_OBSERVER_PRIO, ble_evt_handler, NULL);
What does m_ble_observer stand for ? i don't see any explanation in the whole project...
According to the Overview of this sample, the sample supports the provisioning of the IoT device using "Azure IoT Hub Device Provisioning Service (DPS)" to an IoT hub; and...
I am developing firmware for nRF52811 and I can't get UART working.
Sending data over TX works fine, but every time I try to receive something from RX, I get an error. ...
A short digest of the parenting topic ( https://devzone.nordicsemi.com/f/nordic-q-a/76906/nrf9160-siba-unable-to-connect-to-nb-iot-network-and-resets-every-10-seconds: ) ...
