Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
Hi!
I am developing on a custom board and only have the Debug in connector P3 from nrf9160dk to debug the board. I want to send AT commands to configure the modem and will...
I am a systems engineer helping my team in the component selection phase of the project that involves BLE communication between our master side and a simple remote control...
I have issue to program nrf52832 with nrfjprog command line.
my program use nrf52formesh sdk. I developed with Segger Embedded Studio with GCC on the Linux PC. I modified...
Hello all,
I have successfully installed nRF Connect, nRF Connect SDK v1.6.0 and SEGGER Embedded Studio (SES) v5.50.c to run and debug some samples on my nRF5340 Development...
Hello everyone,
I CAN NOT include the ocrypto_ecdsa_p256_public_key.h file into my project.
What are configurations I need to enable?
I'm new to NCS, could you provide...
Hi, Nordic
This is the test result that I use nRF52833 as the host to connect the slave, slave txpower = 0dbm.
And use Wireshart Sniffer to grab the air packet when...
Hi.
I recently started work on some projects where I have to use I2c OLED and BLE. I used OLED to display time which is running on an internal RTC of nrf52832.
Now I merge...
Hello sir,
i am using nrf52832 board and i am getting following error when i build the code are as follows:
1..\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol...
Hello,
I am trying to change the device name in the ble advertisement in the secure_bootloader example.
Module model: nrf52832
Sdk: 15.2
I have tried to put...
Hello Nordic support,
I am working on a Zigbee coordinator application to make it work with an IAS zone Zigbee device.
As per the Zigbee device specification, ''when it...
Hi , I want to send a char data through bleutouth using ble nus I am using this method
I don't have any error but I don't receive any information on my android application...
I am using nRF Connect for Android and had a question about a script I would like to develop: for this script, I would like user input to specify part of the value I write...
On the nRF 52840, is there a way to have the TWIM peripheral suspend a transfer after transmission of a single byte? The TWI peripheral provides the BB_SUSPEND short, but...
Hi engineer,
i am running a example:SDK 12.2/ANT/ant_bpwr,MCU:NRF52832;i want to dynamically modify the value of "CHAN_ID_DEV_NUM" by reading the UICR value for distinguishing...
I am trying to figure out how to use the SAADC component of the nRF52840 to measure an analogue input and report it as an attribute in a Zigbee end device. I have, so far...
