I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
The SDK version is using version 17 and I am using NRF52832.
I checked the following scope waveform for the next SPI communication.
Question
I want to remove the...
nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_bootloader\pca10056_ble\arm5_no_packs
Why the compiled hex file is different from before, and the code is not modified
I like to use nRF toolbox to monitor my glucose meter. To my understanding, after the glucose device connected with nRF toolbox, they will be exchanging data. So my question...
Hi,
When attaching external GPS Antenna to Nordic Thingy91, I realize that the power consumption increases by about 5mV. Are there any ways that I can config to unuse this...
I just solved this bug, so I'll share my solution.
Bug description: cannot run application after upload via nRF Connect v3.6.1 - Programmer using MCUboot. Upload is successful...
Hello,
I am ble to connect with nRF 52840 using pygatt bluetooth command.
sudo gatttool -b E5:3B:A6:E1:58:86 -I.
[LE]:connect
[LE]:Connection Successful.
Even...
Hi,
I'm using nRF5_SDK_17.0.2_d674dde\examples\peripheral\twi_master_with_twis_slave\pca10040\blank\ses to check I2C as per infocenter TWI testing document.
I have done...
Hello,
I've been using https://github.com/NordicSemiconductor/pc-nrfutil for few years now as a library of my own application to do DFU of a device. Everything worked and...
I am using an nRF52 DK and running a modified version of the heart rate collector example from the pc-ble-driver-py repository.
My modified program scans for connectable...
If you can expect the data to be sent or received at random times over UART, does it make sense to suspend the UART in the driver? Is it fine to leave both TX and RX enabled...
We are building a device where nRF9160 acts as a master that runs Zephyr OS (using NRF Connect SDK). Our device has a 2nd communication interface beside the nRF9160 modem...
Good afternoon.
We are engaged on a project that entails the simultaneous, independent development of two separate modules capable of interacting with the BLE stack. ...
Hello,
Im trying to debug my fw using Keil, its running in debug mode and I have RTT printouts, but once softreset occurs debugger doesnt halt it. Device reboots and starts...
fdsa
1.) From the nRF5 SDK I am using the example project for the Adafruit NFC Tag Reader.
2.) Using the project "as-is" I am able to get some basic information about...
Hello there,
I used both the oscilloscope and PPK to measure the current values. But both values are weird.
First, the PPK shows the current as large as 82mA. And...
