Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
MY CHIP is NRF52840, EVB is PCA10056
SDK: nRF5_SDK_15.0.0_a53641a
bootloader use secure DFU example: \nRF5_SDK_15.0.0_a53641a\examples\dfu\secure_bootloader\pca10056_ble...
Hi,
I found your PDM Working Example. However I wonder what to make of the data I get.
What is the CONFIG_PDM_BUFFER_SIZE_SAMPLES for? Do I get 16Bit Bit-Schemes from...
I am using SDK12.3.0 + SoftDevice S130 in nRF51 DK.
I create 4 channel PWM (+ppi) in timer1 & timer2, because I know timer0 is used by Softdevice, RTC1 by App_timer.
My...
This is more of a Segger question than an Nordic question, but it seems enough folks here use J-Link tools that I could ask here.
RTT Logger and RTT Viewer doesn't log the...
Hi Nordic community
I want only send data using ble app_uart example with out receiving anything. So i tried to send the data that i received from my device to my android...
I am working on the safety-critical system, I have, ON and OFF function, the entire system using UART communication. In which I am using the nrf_queue() and push the data...
Hello everyone,
I have been using nRF52832 module from Raytac ( link ) for my circuit and I got a trouble with sending advertising packages to other master devices. I installed...
Hi,
I am trying to merge working code that places the microcontroller in system_off when a switch connected to pin 16 is opened. It then wakes up the micro controller when...
Hi, I am working on application where I need to store some bigger files. I chose to use sdcard, but I get weird behaviour. Some sd cards, this looks like totaly random ones...
Hello,
I am playing around with the Blinky example on my custom board, where I have one button and two leds. Everything works fine and I can control the LED2 and detect...
I am using the nRF52832 chip with an SDI connected microSD device. I am able to communicate with the microSD card formatted as FAT32, store data, read data all with the FATFS...
I made my own board in which nRF9160 is populated. It's connected to JLink through SWD. SWO is not connected.
I tried rtt debugging and seems to work correctly, but I'm...
Hello,
I am trying to include bsd.h to my project.
simply typing '#include <bsd.h>' is not enough. I need to add directory 'nrfxlib' but I have no idea how to do that...
Dear Support Team,
We are working on nRF52832 based custom design. We had interfaced 3 different sensors (i.e. one with SPI and 2 with I2C bus mode) and sending continuous...
I am facing a strange situation with my app. After turning off all my peripherals and switching to the most minimal code, I see quite a lot of current consumption and that...
