Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
I got this project to compile and work: https://github.com/NordicPlayground/fw-nrfconnect-nrf/tree/master/samples/nrf9160/gps
I have the latest radio firmware at this time...
Hi Sir or Madam
nRF52832 support ANT+ function using 2.4G ISM frequency, but i am not sure the frequency list and channels number/ frequency bandwidth, is there any software...
Hi,
i am trying to interface ultrasonic sensor with nrf9160, but i dont get any examples regarding ultrasonic. so i tried the interrupt method to measure the time of gpio...
nRF52832 Product Specification v1.4 states:
11.3 Writing to user information configuration registers (UICR)
User information configuration registers (UICR...
Hello Nordic team,
I'm currently looking into TLS on nRF52840, I'm using nRF SDK 15.3.0.
I have seend the DTLS example "nRF5v15.3.0\examples\iot\dtls\coap_client" that...
Hello Nordic experts,
I am doing SDK 15.3.0 usbd_hid_composite example and this is where I am: https://devzone.nordicsemi.com/f/nordic-q-a/50447/nrf52840-usbd_hid_composite...
My firmware goes into system off state when idle and wakes on GPIO (button input). I want to display an indication to the user for a fixed duration, so I will modify the bootloader...
Hi,
I'm using nRF51822 chip and SDK 12.3.0 library to develop the software. We want to control the motors with PWM. But since PWM consumes a lot of power, we decided to...
Hello.
For My personal project , i would like to develop a buttonless OTA DFU on my Red Bear Nano V2 (Based on nRF52832 SoC Chip) . Im using the SDK11 and i have folloawed...
I'm trying to add RTT support into the secure BLE bootloader to get debug logs, but after adding the files it's consuming too much flash:
Is there any way to fit RTT support...
Hello,
I tried copying code from twi_sensor example to ble_app_uart and got this error:
Error[Li005]: no definition for "nrf_drv_twi_init" [referenced from W:\MODIFIED_SDK_13...
It takes time for fs_event_handler to be called back after nrf_fstorage_erase is executed. In SDK13.1.0, it didn't take much time, but in SDK15.3.0 takes time to be called...
Hey,
I am using nRF52840-DK and SDK 15.2 and working on 802.15.4. The transmitter is sending beacons at an interval of 2sec. The receiver is scanning the network for beacons...
