Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Am facing issue when am reading data from controller(UART) and using ble_app_uart example code to send data to BLE.
Not able to use two uart's at a time.
My setup: nRF52832 with nRF6707 on top. My embedded application synchronously exchanges UART messages with a desktop application that feeds it data (on demand from embedded...
I use nRF52DK as a central using ble_evt event BLE_GAP_EVT_ADV_REPORT to get RSSI from the peripherals when they are advertising. But once the connection is established, how...
Dear community,
I'm having some trouble configuring and adding subscription addresses to one of my node's Generic On Off Server model. This devices is composed of the usual...
I am new to GATT services and characteristics. I have written one custom service with two characteristics for my custom board. I have used nrf 52832 with sdk 15.2.0 and referred...
Hello,
I am trying to connect to my nRF52832 through J-Link v6.22g. This version doesn't contain the RTT Viewer GUI, but instead I am trying to connect through the RTTLogger...
Hello,
I'm using the nRF52840 in a new design, following the reference designs as a guide. I've noticed that the reference layout files and the development kit use a different...
I've been trying to integrate the Mesh SDK 3.1.0 alongside the nRF5 SDK 15.2.0 on a custom board. I've integrated the light switch server example as part of the code (replacing...
So i was merging a code from peripheral to dual mode which caused my softdevice to change from s112 to s132 .I used the proper flash placement xml file also.After merging...
Hi Sir,
I am use S132 softdevice and it converted to binary file using srecord tool, the add binary file into IAR project seems not working for softdevice.
Below is my...
Hi! I'm brand new to Nordic development. I am unable to get blinky working for the nrf52810 SoC, running off of the Rigado BMD-330 evaluation board; however, I am able to...
I'm having what I believe is a hardware problem on a custom board with an NRF52832. Unfortunately I cannot share the schematic, but will try to describe the symptoms and will...
Hello,
I also think my question seems wired, but I have a situation to make same production of 2 type about BT exist.
I will use 3rd party BT module when BT type product...
Hi all,
I have a problem where I get a Flash page erase failure when scanning interval/window is 3.125 ms (or other very small value).
(SD132 2.0.0, SDK 11.0.0)
When...
