hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi!
I try to write SD to 52810 and nrg go studio can't do it. After recover it can't to switch normal window with possibility erase device and SD write. What possible reason...
SDK 14.2 / SD132 5.0 / NRF52832 --> NRF52832
There is a thread here which discusses "when NUS is ready" : https://devzone.nordicsemi.com/f/nordic-q-a/28208/when-is-nus-ready...
I'm using SDK nRF5_SDK_15.0.0_a53641a, and I was able to trigger the hard fault handler from within the Nordic NFC library. Nothing was running. The microcontroller was asleep...
Hi
Some time ago, we purchased a couple of boards, then (I believe) called nRF52 PDK. They are marked PCA10056.
We need to obtain more nodes. From gleaning information...
Hello there,
I'm looking for a good source that explains the ideology of the Nordic methods for programming and debbuging the nrf5 chips so I'm looking for something that...
Hi,
I'am trying to run the example in Software Development Kit > nRF5 SDK > nRF5 SDK v14.2.0 > Examples > Bluetooth low energy examples > Experimental: IoT Examples > TCP...
Hi,
We have our nrf52840 module going to be ready soon. For production testing, what is the recommended and capable lower tester and upper tester? I am sure that nrf51822...
Hi all I am wrking in an sample be program where ble is advertising everey 5 seconds. I have configured app timer with fire period = 5 seconds in order to read a sensor. After...
Hi,
Ipv6 UUID 0x1820 shall be present in the advertising process. Is it mandatory to put it in the ADV_IND message or can it be in the SCAN_RSP one ? ... the scanner, 6BR...
Currently, we are testing Bonding & Connect.
Please see the attached log below.
If Click 「Bond」 on Android App (nRF Connect), disconnection occurs after "PM_EVT_CONN_SEC_SUCCEEDED...
Hello,
I have the following question: when developing a software product, I developed my own service. It consists of one characteristic and several descriptors (valid range...
On our products, we assign a custom sequential mac address to each unit (we use this number in other places in our system). I believe this is an issue due to the bootloader...
Hello all,
We are using nRf52832 DK.
We are trying to run TCP Client example from IOT.we have even burned the s1xx_iot soft device.We are getting the the error "CMSIS...
Hi,everyone!
I need to configure an external interrupt so that when the interrupt is triggered, I can do something else
When I configure it in the following code...
Hi
Hi i am trying my application for sleep and wakeup without gpio. Actually my work is to put my device(battery powered) in sleep for 5 minutes and after that it should...
