Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello,
I used translation software.
I am transferring test data from nRF52832.
I want to down the average current consumption in data transfer.
I am currently...
Hello,
here i explain the set up.
Cental_A Board :- scanning two peripheral
Peripheral_A Board :- advertise with name Peri_A .
Peripheral_B Board :- advertise with...
Hello,
I would like to know how I can check whether the SAADC is enabled or nor on my application. I am disabling the SAADC with nrf_drv_saadc_uninit(); after configuring...
I'm using the latest SDK (14.1) and have got a working COAP server running over BLE on a nRF52DK, and can exercise the service from my Ubuntu desktop without any problem....
Hai team,
Iam using the ble_app_beacon example program.
I found power profiling calculation on this link devzone.nordicsemi.com/.../ .
i calculated power consumption...
Hello,
I installed the new nrfjprog but it fails to write my nrf52 dongle:
ERROR: nrfjprog failed for an unknown reason. Run the same command again with ERROR: argument...
Hello,i want to get the mac address by sd_ble_gap_address_get().There is a error message as fellow: Undefined symbol sd_ble_gap_address_get(referred from main.o). Where is...
HI!
The use of simulation software I2C and the sensor module communication in my program, without the use of the protocol stack, the normal running of the program, but after...
Hello,
I am using sdk 12.2.2 and pca10040. I want to include the mac address in adv packet name. I am not aware of the api used to get mac address. I used sd_ble_gap_address_get...
HW: BMD-350
SDK: nRF5_SDK_12.0.0_12f24da
Sample Code: examples\dfu\bootloader_secure\pca10040_debug
I have my own firmware app.
Problem:
If I use Keil to flash...
Do I have to temperature dissipation? I attached temperature sensor on my board with nrf51822. I removed copper layer of around the temperature sensor. But it seems the temperature...
Hi,
I am using nrf51822(qfaa), sdk12.3, softdevice s130.
I am using the ble_app_uart (both central and peripheral) as reference for my development.
I have both central...
