I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
Hi Everyone,
I am trying to develop a simple application with the XIAO BLE Sense device, the idea is to send a BLE message with a something hits the device. To achieve this...
To output PWM signal as early as possible after powering on the NRF5340DK, I added the same code in mcuboot/boot/zephy/main.c and mcuboot.overlay as in the app core. This...
I reference the sample at https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-6-analog-to-digital-converter-adc/topic/exercise-3-interfacing...
I have a packet that I am sending out using the nrf52840. Using another piece of code supplied by Emil Lenngren, information from the solar_sensor_beacon project and raw data...
Hi,
I am using the NRF52840 dongles for BLE communication with S140 and the NRF5 17.1.0 SDK. I have plugged each dongle in a Raspberry Pi 3B+, and have set the DCDC regulator...
Hi, We are developing a product which is reading RTDs and thermistors from the NRF52833's internal ADC. We're working on compensating for the intrinsic errors of the ADC and...
Hello,
In my device I have a nrf52840 which communicates with a STM32 via uart.
In my nrf52840 I use the MCUboot.
Is there any documentation or source code that would...
Hi all,
I am developing my own provisioner with the nrf52840 chip. My idea is to be able to add at least 2000 nodes to a bluetooth mesh network with the provisioner but...
Hi, I'm delevoping an appilcation which can generate one sample per 20 us (accomplished with timer0) and transmit one ESB packet when 20 samples are collected. Below is the...
I'm using NCS 2.7.0 and NCS 2.9.0 to read the BT stack version information on an nRF5340. See below for the results.
How should the fw_version, fw_revision, and fw_build...
Hello Nordic-team,
I´m currently developing an application which has been based on a 54L15DK an I´m using an overlay file for adjusting the ports to my own hardware. That...
I/ trying to read the ID of a Fijitsu FRAM type MB85RS4MT using the Nordic device nRF5340. I can properly initialize the SPI and transmit the RDID =0x9F command. The FRAM...
Hi,
I'm working on implementing a modem upload feature (using probe-rs) to be integrated into our production programming line.
Following the procedure described here ...
Hello,
I am trying to use the SAADC peripheral on my nrf5340dk without using the zephyr API; I am writing my program bare-metal. My goal is to set up the ADC in continuous...
Hi everyone,
I'm quite new to the Nrf Connect SDK and Zephyr.
I'm trying to implement a simple DFU (over UART) bootloader. The idea is that when the microcontroller powers...
