Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hi, all
I'm going to develop a crypto application, and tested on nRF52840 with nRF5_SDK_17.0 CC310 run-time library.
there are a need is compute public key from a known...
Hello,
We are currently using the 0.27 and the 0.26 PINs of the nRF52840 for I2C communication as suggested in the sample code. But we need to use the P1.12 and P1.14...
Hi,
I am using nRF52840 as a peripheral + want to add UART to communicate with like Arduino and GSM. Is there any project that I can use/follow. Thanks.
I see LESC_DEBUG_MODE defined in some of the examples in the SDK (17.0.2) but I can't see where this definition is referred to in any of the libraries, so I don't think it...
I am facing strange issue when I execute firmware with NRF_LOG_ENABLED set to 0.
During BLE communication, Firmware is crashing.
If I enable NRF_LOG_ENABLED, all is working...
My requirement program flow is clearly written down .Please help me out.
void USART_EVENT_Handler()
{
// disable timer 1
//disable timer 2
// clear timer 1 count...
HI,
I have already got output from each of the SHT20 and MLX90614 sensors. Now I want to combine both the code. Regards, I need an help to Setup prj.conf file
Thanks &...
I'm referring to the HID keyboard example (BLE peripherals)
The example itself is more or less working and since my goal is to send a whole character string via BLE and...
Hello, Nordic!
When a scan is started with certain scan parameters, a timeout event (NRF_BLE_SCAN_EVT_SCAN_TIMEOUT) will occur in a time less than the specified timeout...
How can I do a point multiplication in NRF52840 using the ECC hardware accelerator for the secp256k1 curve? Also are there examples or any documentation on how to implement...
Hi,
I'm openning a new case (following the proposal of Einar Thorsrud ).
I want to do a BLE NUS project with custom service 128bits and with custom characteristics also...
Greetings!
Using the NRF52840 PDK, I succesfully erase, write and read without any modifications!
I have custom boards which involved a NRF52840 and a MX25R6435F (so same...
Dear Nordic Support,
My project is split into two parts: A firmware application that is based on the Generic Level Server model example (from the Mesh SDK) and an Android...
Good morning,
I'm working on nRF5 SDK v17.0.2 and I am using Segger Embedded Studios (SES) for the development.
I'm having a problem when I want to share my project...
