Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hello,
I am trying edit and compile mcuboot and ultimately upload to the nrf9160.
To do so I am loading the mcuboot project using CmakeLists.txt at v1.2.0\bootloader\mcuboot...
Because the nRF52840 consumes an additional 1mA when QSPI is activated, Nordic has previously recommended deactivating QSPI when not in use, which in practice means deactivating...
Hello DevZone,
Perhip: PCA10040 SDK 15.0.0, SD 6.0.0
Central: PCA10056 SDK 15.0.0, SD 6.0.0
I am working on a BLE project and we need to make sure our link is secured...
Hi,
I am building an application for Thingy:91, currently using SDK 1.3.0. The application is supposed to collect data using BLE and forward it with LTE to the MQTT broker...
Hi,
I wanted to read all the android notification using an embedded BLE device..
I have gone through BLE_ANS example which is in nRF51 SDK, All i want is to implement...
Hi, I'm working with nRF52840DK. I need to run in Direct Test Mode, and to see RSSI & PER. I tried nRF Connect - Direct Test Mode, but it shows only the number of received...
Hi engineers,
I want to transplant demo "usbd_audio" from pca10056 to pca10100, what should I do?
I found a relevant ticket said that
Change board config.
Change...
Hello DevZone,
For a project I'm using the TAG-4 NFC writeable NDEF message example in my SDK and I had a question if this message is always stored in flash or if it is...
I have two nRF5340PDK, both of which would have worked normally. Then I accidentally download the firmware of 52840 version into nRF5340PDK by GProgrammer, which made them...
Hi,
How can I know whether the BLE link between my nrf52840 device and the pc (while connecting via NFC) or the mobile, is configured as a half duplex or a full duplex...
Dear,
I am trying to get secure serial DFU working on our custom board, which is connected to another controller through 2x UART(P0.02, P0.03, P0.30, P0.31) without HWFC...
Hi, I am developing a central application that should get data from a single or even multiple primary services with multiple characteristics in Zephyr. I am using the central_ht...
I'm trying to build the light switch example. I have downloaded the nRF5 SDK for Mesh v4.0.0 and the nRF5 SDK v16.0.0, and place those 2 extracted folders in the same folder...
It works when I use I2C_2 to communicateon nrf9160. The register value is successfully accessed when i2C_reg_write_byte() is called.
9160dk_9160ns.overlay:
I want...
I am trying to use peripheral/spis as a reference for configuring my nRF52840 DK as a slave. The SPI clock frequency is 1 MHz. The SPI master is another micro-controller....
