Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
I'd be grateful for some assistance with what I may be doing wrong.
I have programmed the serial example on a device and the server example on another device.
Copied the...
Hi everyone:
I was testing the bonding with passkey entry, but it seems failed.
The slave 51822 EVK board is set with "BLE_GAP_IO_CAPS_DISPLAY_ONLY" and "MITM = 1".
...
Hello devzone! I am using translation.
I am using a DK board (PCA10056) to examine the current consumption of nRF52840. I commented out the advertising_start() of the SDK...
Hi, I'm trying to implement a mesh serial node with LPN capability, where the UART can be disabled to save power, and then re-enabled via a GPIO.
I am measuring current...
Ok -
I've been through this a few times and read the forums, but the current build system is broken. I'm trying to compile (not even load the board at this point) the ble_hts...
Whichever input channel I select, I always get a value close to zero. Here is my test code using VDD as the input source:
In this case, RTT reports that the value...
More of a plea than a problem. When I migrate to a new version of the SDK I try to be very careful. So, I use sha256sum to check all similarly named files from one version...
Hi,
I am trying to read the SFDP (Serial Flash Discovery Parameter) register of a Micron NOR flash memory using nRF52840 QSPI peripheral. The read SFDP register op code...
Hello,
i work on nrf9160 dk
I would like to know if it is possible to use an AT firmware to be able to easily switch to LTE-M, NB-IOT, send sms, switch off the modem...
Hi.
I am using nRF52840 & SDK 15.0.0.
I set the advertising slow timeout to 14 min, But, the advertising stops at about 3 min.
The followings is summary of advertising...
Hi all,
I'm using nRF52 DK.
I'm developing a program based on 'ble_app_uart_c' example with custom UUID.
When I type command using UART, central device send signal to...
HI, I have following errors while building a project in segger embedded studio:
1. 'TIMER1_INSTANCE_INDEX' undeclared here (not in a function)
2. 'TIMER2_INSTANCE_INDEX...
Hi,
Trying to compile one of the examples provided in the nRFgo SDK 2.3.0.10040 I get an error in the linker (error L204) Invalid Keyword. It seems to refer to REMOVEUNUSED...
Hi, When installing the nRF Connect SDK by using GSA application on macOS 10.15.3, at step "Installing the toolchain" I get stucked to a verification failure for python3 dependencies...
