hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello,
I am working on a custom nRF52840 module based board, using SES v14.2.
How can I control what is printed on the debug terminal, or what has highest priority to...
I have a BLE device for which the local name contains and apostrophe. When I run nRF Connect on an Android phone and view the raw data for this device I find the apostrophe...
Hi all,
I have an nRF52 acting as Central, and it will act as beacon just when it, for example, reach a temperature above a certain point. After some time, e.g 10 calls...
Using SDK15.3.
Using the logging in deferred mode with RTT viewer.
Getting the errors below from the macro expansions but I can't identify what is missing.
Went through...
Hi,
I made a temperature logging device using nRF52832 (SDK 12.3.0). The temperature sensor is read over I2C every 5 minutes and data is sent over radio communication. There...
Hi,
I have setup the SW project to run run FreeRTOS with BLE stack initialized and nus service started without doing any further BLE use after init in runtime. Sometime...
Hello,
I am using an Adxl362 accelerometer on nrf9160 dk board.
I followed the tutorial a to add the overlay file and even configure the pins i want to use by flashing...
To the kind attention of Nordic support team,
It seems gazell is a very good candidate to be used in tipical working environments, where a bunch (<= 5 devices for example...
Hi,
I am new to Nordic. I bought an NRF52 DK and a Fanstel EV-BT832 development board. As you can see in the picture, both boards are connected to the computer via USB....
Hi,
I had some of your example projects which were being evaluated within Keil and SEGGER and now have an issue with Keil after updating to the PRO license.
I now get...
Hi,
For a peripheral reset, I was recommended to use the code below.
I was just wondering about what the middle line does. Is this a kind of delay to make the reset...
I am trying to start the mesh alongside GATT profiles. I am getting error NRF_ERROR_NO_MEM when calling sd_ble_gap_adv_set_configure in mesh_adv_data_set, which is called...
Hello,
I get the following output when I try to debug the Zephyr's button sample with SEGGER Embedded Studio:
Preparing target for download Executing Reset script TargetInterface...
For the nRF52833:
The product specification is contradictory on the 2 UARTs available. Would you please clarify?
UART0 is this a legacy UART only or does it have Easy...
Our customer has requested access to any test suites the BLE IC vendor can provide which can be used to provide objective evidence of testing & specific test cases.
We started...
