Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
In nRF5_SDK_15.0.0_a53641a code, there's such definition:
#define UART_DEFAULT_CONFIG_BAUDRATE 30801920
Which means about 30.8 Mbps.
But in page 345 of nRF52832's...
Hello,
I'm using a nrf51822 board as a DFU controller to update another board's application, the client board runs the bootloader secure example. When I write data to the...
This is almost certainly a noob (to nRF52840) programming question.
I have modified the peripheral/gpiote example to invoke an ISR on the falling edge of a pin signal. In...
I am trying to use the Sparkfun nRF52832 breakout board as a master in I2C communication. I am using Arduino IDE to program the module. I defined pins 24 and 25 as SCL and...
Nordic Support, Let me first explain what I would like to achieve. I am developing a line of devices that will act as GATT peripherals. I would like average current consumption...
I have a custom board with an nRF52832 (CIAA-B0), and I am trying to use the SPI Master.
When I use SPIM1 or SPIM2, the transaction hangs, but the same code talking to SPIM0...
Dear Nordicsemi,
We are looking for Sub 1 GHz RF Module, which gives Longer Range distance in Field either in LOS or NLOS.
Please share the details regarding proven...
Hi guys,
We've written a small test on-top of our internal Bluetooth library (glorified wrapper sat on-top of SDK 15.2.0 SD140 6.1.1) on the nRF52840 to send dummy bulk...
Good morning everyone,
I am implementing a custom radio protocol on NRF52 without using the SoftDevice at the moment. For some reason, I get a HardFault which I am trying...
Hello everybody,
I can flash my custom nRF52832-based PCB using the nRF52 DK and Segger Embedded Studio or nrfjprog, but this requires that I always have my computer with...
Hi,
I need to get 1.8V on the VDD using high power mode. According to the documentation this is the default value. However, I measure 3V.
Please advise,
Daniel
I am developing a nRF-Mesh based product. This product consists of a fixed number of nodes in a Bluetooth Mesh Network. Are there possibilities to factory-provision a set...
Hi!
I am working with experimental_ble_app_eddystone in SDK 12.2.0 for nRF52.
I have seen that the firmware does not support using different advertising inteval for each...
I'm wondering whether or not nRF52840 can be used for a USB smart card development.
"According to the spec of a USB CCID device (which could be found on www.usb.org ), there...
Hello everyone,
After using IPSP intiator and IPSP Acceptor BLE Examples on 2 different kits and connecting them through this profile, how do i send IPv6 packets between...
