Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
Custom app running on a nRF52 devboard. Serial port runs when I use the debugger and continues after I exit the debugger, but does not run from a cold start.
using the...
Hi,
In nRF5 SDK v12.3, the members of nrf_ecb_hal_data_block_t are pointers to non-const data. I was wondering if these indeed need to be non-const for the Softdevice S132...
Hi,
I have a central and peripheral device both are based on nRF52. Central device is running on SDK 12.2.0 and peripheral with SDK 11.0.0. I would like encrypt the communication...
Hello!
We're using SDK 12.3 on our application, and we're aware that the SDK is targeted to be event driven, meaning that our code should be the one keeping track of the...
I am using SDK15 , nRF52832 custom board , keil uVISION 5 , ble_app_beacon example.
I am adding timer to the example.
In below code, when I comment out update_vbatt()...
Good afternoon,
I am facing the following issue:
a client application writes to several characteristics (write with no response) I set in my chip, which trigger the execution...
Hello,
We are porting legacy application to the nrf52840. We are using Keil uVision 5.
The legacy code is using some gcc ideas and extensions so we are forced to use...
Hi ， All
I am using nrf52832 SDK12.3.
When the host runs to the discovery service but has not yet discovered the service，the slave power off. The host can no longer connect...
Hi there.
I Tested Example (secure_dfu_ble_s132_pca10040). Fine work.
but I could not find the example code to transfer the firmware.
I need the code to receive...
Hello,
I'm a little bit confused about max datalength that can be read/written in a characteristic.
See attached, a MTU of 64 bytes is negotiated thus 61 bytes available...
hello there! I am working on a project in which two devices(one is central and other is peripheral ) uses Nordic bluetooth controller nRF51822 for connection and data exchange...
I uploaded a sample code into an external nrf51822 module using nrf51-dk as explained by this blog www.instructables.com/.../ . power supply for the external module was from...
Hi
The following ticket explains when I configure pin21 as RESET it will be hardware configured to pull-up internally. https://devzone.nordicsemi.com/f/nordic-q-a/8342/nrf52832...
Hi all,s
I have a couple of nrf52840 boards and i was testing the ble mesh light application. The application works fine, but i changed it so it will periodically set...
Hi, I have tested thingy52-mesh-provisioning-demo in NordicPlaygound on github. It works fine by using a precompiled hex file (via nRFgo Studio) but It doesn't work (light...
