I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Hi Nordc Technical support team;
My name is Ercan. I'm from Turkey. I am a Master degree student in Electronics and Communication Engineering department.I want to make a...
I am adapting the example ble_app_uart_c_pca10056_s140, which is a BLE Nordic Uart Service central device. I would like that other c files can access the variable m_ble_nus_c...
Hi Everyone,
I am working on the nrf52832 and i am trying to build the Eddystone beacon application example with segger embedded studio. But when i do, I get the following...
Hello,
I want to modify the default transmit power of the nrf5340 peripheral_uart project.
board:nrf5340 dk
ncs:v1.5.0
example:v1.5.0\nrf\samples\bluetooth\peripheral_uart...
I am trying to figure out how to enable and use the RNG peripheral of the nRF5340.
since the RNG is on the Network side of the nRF5340.
is there anything i need to set...
This is very reproducible...after sending and receiving data in a loop, the modem application becomes unresponsive. Only modification from SDK software is that I am using...
Hello,
I was trying to setup nrf5 board with IoT sdk for tcp connections where the tcp board will act as a server and raspberry pi 3 model B 1.2 as client.
I downloaded...
I am looking for the following products and solutions.
Products :
nRF52-DK
External input :
ADC 1000 Sampling input
1Hz input 3.3 p-p sinewave
Output :
UART...
Hello Sir/Ma'am,
I have used the ble_app_uart (for pca10056) example code to execute the same.
I referred this link to execute my code https://infocenter.nordicsemi.com...
Hi there,
I am using nrf_mtx_trylock.
The explanation of nrf_mtx_trylock is "Try to lock a mutex.".
I would like to lock a mutex forcibly.
Does the function which...
Hi,
I am using the radio test example code where in the interface is through cli. Our custom board has a serial port in UARTE1 instance
how do I configure the cli to...
Hi everyone,
I am trying to develop an application and I need to solve this situation : when the modem is not able to connect to LTE-M network, I still want to be able...
Hi,
I already replied to an old discussion without response so far:
https://devzone.nordicsemi.com/f/nordic-q-a/57449/nrf9160-mipi-rffe-support-for-more-than-one-device...
