dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi,
I am developing both Central and Peripheral devices with nRF52840. For consistency, both are using SDK 15.3.0 and S140 V7.
I am able to connect to peripherals and...
Hi,
I was try to import modul nrfxlib in extising cmake project. My IDE is Eclipse CDT. Version of Zephyr is 2.4.0. Reason to do that, was testing SoftDevice BLE functionality...
We are using our board design using nRF52840.
During bringup I noticed that I could not run the Softdevice and the SPI driver simultaneous. After a bit of debugging it boiled...
I'm trying to send radio frame in timeslot but it's not working. From what I see with an spectrum analyzer, only the first frame is sent.
I am able to make the radio works...
Hi,
We are developing an application with a custom nrf5340 board in which beacons are sent periodically every 100ms. We have been analyzing power consumption with a Power...
Hi there!
We faced the problem of not being able to perform Legacy DFU with Android 10 and newer iOS devices and have since applied the fix. However, since doing so we observed...
Hello,
in our design we use a RF switch behind the ANT LTE antenna I/O of the nRF9160. Many RF switches need DC blocking capacitors in series with the RF signal due to their...
Hi everyone,
When we want to enable a module we usually enable it from the sdk_config.h by setting the desired module to 1 (for example #define NRFX_SAADC_ENABLED 1). I...
Hello, I am using nrf52810 and S112 Softdevice.
After initializing uart, use uart close for uart sleep.
Then the uart close will be checked.
I want to make an uart init...
I have an nrf52832 based device and a mobile app that I'm working on. I'd like to be able to turn the device on via the app, so wake on BLE seems the way to go.
I'm a neophyte...
Hi,
I am working nRF52832 and sdk 16 version. I want to get the RSSI value of my peripheral device nRF52832 and send it to central (phone) over ble ? how to do that ?
...
Hello.
When scanning with the iOS app nRFconnect, the device name is displayed, but when scanning the same device with the Android app nRFconnect, the device name is "N...
I'm trying to test polling on the Thingy91 using the Asset Tracker firmware. However Ion function sensor_sample_fetch_chan(..) I get returning error: -134. I can't find any...
Hi
I created my own application and want to enable CONFIG_DFU_TARGET_MCUBOOT.
But like the picture shows, this marco is still grey in the dfu_target_img_type() function...
