Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hi,
I want to program my chip nRF51822 ( https://www.waveshare.com/wiki/NRF51822_Eval_Kit ) using the KEIL tool and the ULINK2.
When I try to program the chip KEIL show...
Hi,
I've encountered a problem with opening a project in Segger Studio. I have recently moved to 1.3.0 tag and I am working with Thingy:91 (so I basically open nrf9160 samples...
I'm doing a Nordic example named "Nordic UART Service Client" ( https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v17.0.0%2Fble_sdk_app_blinky.html )
The steps...
Hi ,
I ran the example "zephyr\samples\bluetooth\scan_adv" on the nRF9160 dk kit .
It says the following error
"
2020-07-16T02:22:00.682Z DEBUG modem << *****...
Hi, everyone
A LPN ( Node-LP ) had selected one of nodes as its friend ( Node-F0 ), if Node-F0 is taken away, will the Node-LP automatically reselect other node as its...
I read somewhere for new project we should use nrfx driver because in future old nrf_drivers will not be support and improve. All examples in sdk15.3 as I understand used...
Hi All,
I am trying to implement a battery level reading app using NRF52840 DK. It seems I am receiving a timeout from saadc.
In order to run on the Lithium battery, should...
Hi,
I programmed two thingy:91 to return RSRP and RSRQ to a server. On is running with LTE-M and the other with NB-IoT.
I found something that seems strange : +CESQ: 99...
Hey everyone, I'm trying to use the QSPI module (again) to interface to RAM, not FLASH. I'm not really sure if this is possible, but we'll get there. Right now I can't get...
I've been tested for BT SIG however have met error which sent 0xc000 and got 0xc000. I expected to receive 0x8xxx. Command is LETestEnd.
I tested with nRF51822 customer board...
Opening a project in SEGGER Embedded Studio I have annoying "no entry signs" (white minus sign in a red circle) on the left side various items in a project, whereas most of...
Working with nrf52832_mdk and using basic GPIO functionality, I am unable to toggle the GPIO pins P0.0 or P0.1. The code I am using is quite simple and I am able to toggle...
Hello,
I am working on the mqtt sample from ncs\nrf\samples\nrf9160\mqtt_simple. Mostly the nRF9160 connects to the MQTT server in the first attempt. But sometimes I observe...
Hello,
I work on nbiot evaluation and i try to send udp data from my basement.. I boot and attach network from ground-floor and when i'm on PSM mode im going on basement...
