Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hello!
I am working with the nRF9160 devkit and I have encountered an issue.
I cannot seem to properly enable PSM to use the GPS and LTE at the same time.
In the application...
Hello, For our project we were planning on using a 3rd party module MS88SF2 (nRF52840), which schematic snapshot is provided and which will be powered though the li-po battery...
Hi guys,
I am using the Nordic nrf52832 board for my project. One of my goals is to enable the device to read the voltage from the external source. I have already found...
I think I am having a problem with Radio Notification. I am not sure. I have an application where I need simultaneous “Central and Peripheral”. Device only needs to advertise...
I am trying to do Mesh DFU.
I have done updating ble_app_blinky successfully for the 1st time over mesh but after that, I tried to do again by increasing the application...
Hello,
I am working on a custom board using a nRF52840 based module. I am using SDK 14.2
I am running the following simple code to sense when an GPIO goes to a low state...
I know I can set the TRACEMUX pins to 0 to enable the GPIO instead of SDO. I do this on the first line of the program.
My problem is that when I click debug, from the time...
hi The serial ports p0.04 and p0.05 on our hardware circuit. We can't communicate with the board with nRFgo studio after modification. The serial port has been closed. Request...
Hello everyone,
In the past few days I have been struggling with the following issue: I have a file on my iPhone, I want to send it to the NRF52840 using BLE (the softdevice...
Hi,
I am running the following setup, both on nRF52840-DK:
1. Central : Always scans , when he finds devices with NUS service -> Initiate a connection
2. Peripheral...
My company has a situation where we have 3+ devices.
A is the provisioner (also an embedded device)
B is a already provisioned device
C is a non-provisioned device...
Hi,
I have made a custom board with u-blox bmd-340-A-R-01 module and trying to erase the flash with PCA10040 DK. I am getting error when I try: nrfjprof -e. Please find...
Serial Example in Mesh SDK allowed embedded system to provision a Mesh network
by interactive_pyaci.py controlling nRF52 with serial example with UART.
But the example...
Hi Nordic
SDK15.2 based application and bootloader running on NRF52840 based UBlox module.
We have the following symptoms happening in the field:
- 2 channels of the...
The customer wants to implement a hid function like the nrf52840 on the nrr9160, and there are no off-the-shelf routines or references to add the hid function.
