I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hello,
I want to develop small modules with smart BLE that only sends advertise every 2seconds.
Do you think that the Central module can see all peripherals if the installation...
Hej, I just spent plenty of time finding an answer on above error within here with no luck. Since
there are certainly others facing this problem, I hereby post my solution...
sdkconfig.txt mainc.txt (/attachment/6fb97103178e9eb2c30302351e63ce8f)Can you please tell whether i follow the the entire tutorial as in the link or just the first step for...
Hello, when invoking sd_ble_gatts_hvx, it returned NRF_ERROR_INVALID_STATE (0x00000008), I wanna know what are the list of possible errors, here are a list I made:
CCCD...
Ciao all,
Two weeks ago I have started to learn about beacons and their usage. I have bought pca10040 development kit and designed custom nRF52832 based beacons. After...
Hi,
I've just hit a strange issue with SDK 12.1 on nRF52832.
Usually on BLE_GAP_EVT_DISCONNECTED , sd_ble_gap_adv_start gets called to start advertising and everything...
I am new to nRF 52. Previously i have worked on arduino IDE for programming arduino uno,mega. I have also used MPlabX for programming PIC(MircoChip) series micro-controllers...
Hi,
For the NRF52832, I read that a number of write (per block) is limited before a forced erase of the page. Apparently, the amount of write is 181 times for a block of...
My sensor app is based on nRF UART service and my current case in one sensor (peripheral) one gateway (central).
In a situation where there are two pairs of sensors (S1...
I'm trying to use a low accuracy GPIOTE event to start RTC1. The following code works as expected when using hi accuracy mode but will constantly trigger in_pin_handler()...
Hi, I am using radio with ppi to advertize packets as shown in the mainc file attached. mainc.txt
Even after allocating the access address of Bluetooth on line 196 as set_address0...
Using nRF52832 I am collecting from 8 SAADC channels using example ble_app_uart__saadc_timer_driven__scan_mode as a guide. AIN3 (P0.05) gives incorrect results. Because P0...
Hi,
I have an application that utilizes the dual bank bootloader and s132 soft device on the nRF52832 chip. I am trying to determine the total RAM used and can't seem to...
Hi,
i am using NRF52 and S132V2.0.0 SDK11. i am working on BLE application in which i implemented DFU service to it, so that i am able to observe DFU service and 3 characteristics...
