Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
I have 2 52840 modules with PCB antenna and I am trying to check the max connection range
I followed the recommendations and achieved only 120m.
I cannot use the examples...
Hi, we recently using audio with ATVV service instead of HID service. As we notice, Audio would enable by SR3 itself in ATVV service if we push the key, but not in HID service...
Hi Nordic:
I want to change TX power of mesh-sdk.2.1.1 light switch, I've follow
https://devzone.nordicsemi.com/f/nordic-q-a/34491/mesh-range-power-and-mode
and set...
Hi,
I have bougth one Nordic Thingy 52 and one nRF52840-DK. My idea is to communicate both via bluetotth.
For example, i want to capture the temperature adquired by Nordic...
Hi guys,
I am using the softdevice S120 firmware: s120_nrf51822_1.0.0-1.alpha_softdevice.hex
The error_handler registered when calling sd_softdevice_enable is called...
We are implementing a Nordic NFR52832 using the ARM mbed ble stack that leverages the Nordic SDK using a HID over GATT profile. Windows 10 seems to have an issue with this...
Hi all.
I'm trying to make a list of brands and models of Android phones that have implemented LESC. I appreciate any feedback and experiences working with LESC (numeric...
Hi There,
I just want to confirm which method is being used to perform DFU over thread (Single bank update or dual bank update), and can I perform DFU on Sleepy end device...
Hi,
I'm trying connect NRF 52840 width Intel AC 9260 Windows 10 Desktop/
When I compile and run any examples from nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral and I...
Hi,
when generating settings on windows using nrfutil on one project takes about 2 minutes and it swallows whole memory during the command.
The command i am using is:...
Hello,
I am trying to use nrf5280dk with RIOT OS and Contiki OS. I am following these steps to enable access to the device from os. https://devzone.nordicsemi.com/b/blog...
Hello, I have an nRF52 device with NRF_SDH_BLE_GATT_MAX_MTU_SIZE set to 512 and it accepts connections and the client sets the max mtu to 512. It is on SDK 15
When
an...
I am working on a project involving BLE communication, but I am quite new to BLE, so please be patient.
The project scenario is the following: I have a nRF52 feather board...
Hi Nordic team,
I try to use the secure dfu of web app and test this code： https://github.com/NordicPlayground/secure-dfu-web-bluetooth
but I can not test successfully...
Hi,
I am using STM X-nucleo-iks01a2 sensor board arduino compatible, so connected to nF52840 DK arduino header and want to read HTS221 I2C/SPI interface supported sensor...
